Php-x19w faults - Computers & Internet

Susan, 01435 - Brake Pressure Sensor 1 - Electrical Fault in Circuit. Your vehicle will have to be fixed or reprogrammed by a capable technician. Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."


http://wiki.ross-tech.com/wiki/index.php/01435

http://www.vwaudiforum.co.uk/forum/showthread.php/125450-A3-01435-Brake-Pressure-Sensor-1-(G201)-Fault-and-others

http://www.audizine.com/forum/showthread.php/569585-ABS-ESP-light-gives-01435-code-Brake-Pressure-sensor-intermittent

http://forums.vwvortex.com/showthread.php?3300683-Brake-Pressure-Sensor-Fault-Code

http://forums.swedespeed.com/showthread.php?166473-OBDII-to-Volvo-Code-Conversion-List

Check the attached link

Fault Code:- P0443 Indicates a Power-train fault


The fault is generally due to a problem in the Emission Control area


Fault Description: EVAP canister purge valve circuit malfunction

Action of ECM:- ECM Default: - Canister purge inhibited - Adaptive fuel metering inhibited


After clearing the DTC, complete the Purge system monitor drivecycle
Check for a reoccurrence of fault DTC.

Possible Fault:- EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure

Check fault codes here http://www.bluejag.co.uk/diagnosticcodes.php

How to read ECU fault codes. 1KZ-TE & D4Dwww.pradopoint.com/showthread.php?...to...fault-codes.-1KZ-TE...Cached

http://www.ukwhitegoods.co.uk/modules.php?name=Forums&file=viewtopic&printertopic=1&t=7502&start=0&postdays=0&postorder=asc&vote=viewresult&popup=1
Above is the answer is discussed in detail, this should help you solve your problem.
http://www.ukwhitegoods.co.uk/modules.php?name=Forums&file=viewtopic&printertopic=1&t=31925&start=0&postdays=0&postorder=asc&vote=viewresult&popup=1
http://www.howtomendit.com/answers.php?id=71337

Unfortunatley your monitor is going out. I just had that problem. My sceen would come on, but after about 10min. it would blink off and turn black. I would have to hit the off button on the monitor, then turn it back on. It would work fine for a few minutes then black out again. I got a new/used monitor where I no longer have that problem.

I did check to make sure my hybernate was not activated, it wasn't, I had it set to never turn off.

Good luck.

I've just spent ages tracking this one down. In my case it is the protection circuit in the backlight invertor. The tubes are worn out (they are pink when they first come on) and need replacing :((.
If the picture disappears and the blue light in the ON switch stays on, you've probably got the same trouble.

You should have recieved a 3.5mil stereo lead for this it is blue on one end (L shaped) and green on the other. If you are not using any other speakers then plug either end in the green audio socket on the monitor and the other end connects to the green audio ouput on your computer.

ignore the fact one end is blue.

Hope this helps.

just an update...I have fitted a new cable (pc to monitor) and it has been on for 2hrs now so fingers crossed!