My ge wbvh6240fgg front load washer will not spin or pump the water out. I have pulled the plug and waited a minute then pluged it in again. No success. It goes into pause. I can hear a quied moterized soud when I put my ear up to the washed.

Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

Hi,

This a common problem for all front loaders. Your washer will not drain or work 'cause your outlet filter is clogged or an unusually heavy load. The small door is on the left side front bottom of your washer. Remove the door with a putty knife or thin butter knife inserted in the middle top of the access panel door. Drain the water from the filter housing by pulling the tube out of the clip and unplugging, allow it to run into a bucket while the machine is in spin only mode. This mode is acheived when the washer is first powered on press the spin button until no spin is reached then run. Run in this mode until no water is draining from the tube in the bucket. Keep the tube as low as possible. When water has stopped coming out of the tube turn off the washer and unplug from the wall. This step is important because this resets the fault. Expect some water to come out when you open the filter housing by turning counterclockwise until you can pull the filter from its housing. Clean out your filter, return to housing turning clockwise until seated and recap the tube and place in the holder, refit the cover and plug back into the wall. Fixed. You may also need to lighten the load a bit but I always try full on load anyways. If it fails again just lighten, unplug wait >1 minute then replug and run.

Goodluck..

I would take filter out of drain Pump and check for obstructions. There will be water gushing out when filter is removed, so be prepared.

i've had the same problem until i pluged it directly into the wall socket not with a drop cord that way you can get the full voltage needed to run the machine and don't plug it in a socket that has other items pluged in it

I found the hose hooked to the pressure was clogged down at the tub end. So it couldn't send a signal to the switch telling it the water had pumped out and it was time to spin out, the plugged hose was holding pressure telling the washer (falsely) that the tub had water in it so it won't spin if it thinks water is still in the tub. By pulling the hose off the switch end and blowing thru it to clear the lint and soap slime that was plugging the other end it works perfect now.

Electronic motor needs to be reset. Unplug for 2 minutes, plug back in, open and close lid slowly 7 times to reset computer. Also check to see if belt is not broke, pull up top, remove front cover, just lifts off, check belt.

The most common reason for no pump out is a blockage in the pump. Best to drain as much water as possible. (even laying the drain hose down to allow as much of the water to drain out as possible) Un-plug washer. Next, open the front of the washer by using a putty knife to push in and release the clips about two inches in from each side at the seam where the front panel meets the washer top. Pull the front panel forward and lift it off the bottom pegs. Remove spring clamps from inlet and outlet of pump with a plier. Remove two pump mounting screws to allow pump removal after unplugging electrical leads. Remove obstruction from pump. Most pump bodies can be separated if necessary. Reassemble, plug back in and test.

I have a GE WBSR3000GWS Model and it stopped spinning at one point as well. My service guy came out and did the procedure below and reset it with in minutes.

How to Reset your GE Washer :
1. Turn the dial like your going to wash a load but do not pull the knob.

2. Unplug the washer from the wall and wait for 30 seconds.

3. Plug the washer back into the wall.

4. Lift the lid 5 times to at least 6 inches high. Open/Close within 15 secs.

5. Pause… You should here a click. If you do not, then repeat 1 – 5 again.

6. Insert a towel or garment into the washer and then pull knob to start the wash cycle.

7. Check the wash cycle to make sure the washer is agiating and spinning during its cycle.

GE Answer Center : 1-800-626-2000 opt 3 - for more information
Lale

pump might be pluged or something caught under the basket in the washer.

Sounds like u might be having trouble with the lid switch.. U need to also check you water pump out.. this model has a electric pump that may be plugged... dont take much to plug this pump up.. have you taken front panel off yet ? Post what ya find