I forgot to set up my password to my dlink wireless router how am i going to do?

Default user is Admin and default password is blank. (Don't type anything)

If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.

From: http://www.scribd.com/doc/6254595/DLink-Dir655-Manual-Wireless-N-Router

You can download the manual from this WEB site.
ftp://files.dlink.com.au/products/DSL-G604T/REV_A/QuickInstallGuide/DSL-G604T_QIG_v1.00.pdf
Page 8 gives you instruction on changing the password.

You will need to login as admin and set it up again. Connect per ethernet cable, open a browser and enter 192.168.0.1 You should see a router welcome screen or logon dialog login as admin the default password maybe one of several things depending on the particular revision/edition blank/null 'admin' 'password'
Support for this model is available at http://www.dlink.com/products/?pid=DI-524&tab=3 manual at ftp://ftp.dlink.com/Gateway/di524/Manual/DI-524_manual_06292005.zip
Once you're in you will have to set up an ISP connection which may require your ISP username / password and selecting a protocol particular to your ISP and setting up the wireless WEP key

You need to go into the DLink wireless router's configuration.
Connect a LAN cable from your computer to the DLink's LAN port, open a Browser and enter the DLink's configuration URL (http://102.168.0.1)
login and enter the admin password. Then go to the wireless settings and change the wireless channel.
For information on securing you wireless network, configuring the wireless router and configuring the wireless card in the computer, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security
If you have difficulties, please add comments and give me details of the problem and error messages.

You reset the D-Link back to the factory default by - Press the RESET button at the back of the wireless router when it is powered up. Holt the RESET button foe at least 5 secs until the LEDs flash and then release the RESET button.
You can then configure the D-Link as follows ;-
To set-up and secure the wireless router from unauthorized access, follow these steps: -
1. Connect the wireless router to your computer with a LAN cable.
2. Start your browser and enter the router's configuration URL IP address.
3. Enter the router setup, login and password
4. Change the admin password
5. Go to the wireless settings and change the default SSID and turn off SSID broadcast.
6. Setup encryption key the strongest is WPA2 (if not then WPA).
7. For further security measures - turn on MAC address filtering and enter the MAC address of the wireless cards on the computer/s you want to connect to this wireless router.
8. Record the settings you have made and keep it in a safe place and Save the settings.
9. Configure the wireless cards on the computer/s with the SSID and encryption settings of the router.
10. Remove the LAN cable between the router and the computer then the computers should be able to connect to the router wirelessly.

Hi there,

As an initial info try to do a hard reset on the unit, this process will restore the system into a original settings. you can find the reset switch on either on the left of right sight of your router.

or

you may visit this SITE to recover again your current password without erasing or removing the current settings made.

Reset Password.

Hope this idea helps you.

Thank you for using fixya.

Open out a paper clip, pull the power connection out of the back of the DLink.
On the back of the DLink is a tiny hole with "reset" written above it, poke the end of the paper clip into the hole untill you feel a tiny switch click down, hold the switch down and put the power plug back in (this takes three hands) hold the switch down for ten seconds and your modem/router will be set back to factory settings.
username Admin
password Admin
try admin and try with username only or with password only.
It's been a month or two since I did a DLink and I cant remember which it is.

Type 192.168.0.1 (you can type the router address if you have changed) and enter on browser's addressbar. Router's interface will appear.
Click on SETUP and Click on the WIRELESS SETTINGS at left side. on the page you will see the option of WIRELESS SECURITY by drop down menu you can choose the Security mode that you wish. here is the link for the emulator
http://support.dlink.com/emulators/wbr1310_revB/wireless.htm

Please post your question if you need further assistance
Good Luck

Hi, To enter the webinterface configuration of your D-Link 524, type "192.168.0.1" at the address bar of any browser. UserName is "admin" and password - leave blank. Good luck and kind regards.