Question about Zanussi 24 in. IZZI ALU Built-In Dishwasher

1 Answer

Zanussi izzi starts up and after 1 minute it stops with flashing plus light. whats the problem with it

Posted by Thomas Gilgan on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Did u ever get this sorted and wat was the problem??? mine is doing the same!! any help wud be great ..

Posted on Jan 12, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, my zanussi izzi dishwasher has started acting up, it will start a cycle but after a couple of minutes it trips out the main RCD in the fuse board, now i have isolated it to the dishwasher itself and...


If it trips after a few minutes of coming on , it is probably the heater which is faulty , disonnet it and try , if it doesn't trip you need a new heatee

May 02, 2017 | Zanussi 24 in. IZZI ALU Built-In...

1 Answer

I have a zanussi izzi and it works ok for about a minute and then it stops working and the programme light starts flashing continuosly?? any ideas?? water comes in fine and wash pump works for about a...


Hi

The issue can either be with the unit not draining properly or the timer/electronic board itself has gone bad & should be replaced. First clean the drain hose and the drain pump for any clogs, you can do this by taking off the bottom access panel. After cleaning if still the issue is not resolved then the timer/control board has gone bad and needs to be replaced. Hope this helps...please post back for further assistance.

Daniel

Jan 12, 2011 | Zanussi 24 in. IZZI ALU Built-In...

1 Answer

Zanussi ZDT6252 stops 1min into cycle


You need to reset the computer on the bottom. Had the same problem with mine. The Blinking led means the heating element is bad and will not operate.

Dec 30, 2007 | Zanussi 23 in. ZDT6252 Built-in Dishwasher

2 Answers

ZDT5052 flashes quickwash light


Tarvi...I don't know what the problem is...hard to diagnose these things. If the unit is working correctly, I suggest that you simply cut the power for a few minutes and then restart it. That may clear our a trouble code.

Dec 06, 2007 | Zanussi 18 in. ZDT5052 Slim-Line Built-in...

2 Answers

Machine won't start and the START light keeps blinking


A flashing start button shows that the filter is dirty. Remove the filter assembly from the machine. The "tube" can be split into 2 sections fairly simply - do so, and wash each piece under the tap to clean it.
Once the assembly is cleaned properly, select the program that you desire, and press and HOLD the start button for 2 seconds. The wash cycle should begin.

Nov 05, 2007 | Zanussi 24 in. IZZI ALU Built-In...

2 Answers

IZZI Built-in Dishwasher


Turned out there was a block on the clear short pipe that goes to a pressure sensor situated to the left at the front behind the front facia under the door which the engineer cleared by blowing it!! The pipe connects to a little stub that sticks out of the blue plastic flow control thing on the lhs of the dishwasher. U can access this by removing the lhs cover but not really necessary...

Aug 31, 2007 | Zanussi 24 in. IZZI ALU Built-In...

1 Answer

Zanussi FX1465W aquacycle, beeps 5 times and end light flashes


I have the same trouble with my washing machine did you find a solution i have been told the PCB or motor drive system

May 19, 2007 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Zanussi 24 in. IZZI ALU Built-In Dishwasher Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Paul Carew

Level 3 Expert

3518 Answers

Renee Knafel-Bullock
Renee Knafel-Bullock

Level 2 Expert

355 Answers

ray gallant

Level 3 Expert

69189 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...