Blinking lights on kenmore 665

Kenmore Elite dishwasher Smart Wash light blinking
Sanitize Blinking Light
Some Kenmore dishwashers have a sanitize feature; when this light blinks, it means the sanitization step failed because the hot water in the dishwasher did not achieve the desired temperature or the final rinse cycle was interrupted.

How to Reset Codes on a Kenmore Dishwasher - Hunker

https://www.hunker.com > ... > Dishwashers
Search for: Kenmore Elite dishwasher Smart Wash light blinking
More here

https://www.applianceblog.com/mainforums/threads/kenmore-elist-665-dishwasher-smart-wash-red-light-blinking-machine-not-working.29342/


https://www.google.com/search?q=kenmore+elite+dishwasher%3F+The+smart+wash+light+blinking

FIXED Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry ...

www.applianceblog.com/.../40588-Kenmore-dishwasher-lights-flashing-...

Aug 26, 2013 - 10 posts - ‎3 authors
Thread: Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry" ... A few months ago, we had a brief power outage and the next morning, noticed the "Hi Temp" and "Heat Dry" lights were flashing. ... Well since then, the dishwasher intermittently stops mid-cycle and these same lights ... Thread: GE Eterna QuietPower 2 Normal and Heated Dry ...
6 posts
Feb 24, 2012
Kenmore Elist 665 dishwasher Smart Wash red light ...
6 posts
Dec 23, 2011
Heated dry blinking +17 times - ApplianceBlog
10 posts
Nov 14, 2010
Heated Dry light blinking
3 posts
Nov 7, 2010
More results from www.applianceblog.com

Why won't my dishwasher start and why does the "Heated Dry"

www.shopyourway.com > Manage My Life > Questions

Nov 16, 2009 - When I hold down the Heated Dry button to turn the control lock on it ...my dishwasher start and why does the "Heated Dry" light keep blinking ...

Sound like you have a bad control console, which will need to be replaced.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

To reset and run diagnosis on the model 15899100 Kenmore Dishwasher you need to press the following buttons on your front panel. Hi Temp, Air Dry, Hi temp, Air Dry. The sears service technician just left my house and used these codes to reset and run diag on my washer.

Hope this helps

Hold down the "HEATED DRY" button for 4 seconds to unlock.
Try to press these botton in sequence,Heated Wash, Heated Dry, Heated Wash, Heated Dry.release your hand, the unit will go into diagnostic mode. that is all leds will ON for a few seconds,and start normal operations.
If that does not work, you might need to check the electronic control board if the ribbon is seated properly.
Finally solution, is to change the electronic control board.

Push the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. This will clear any existing faults and should return the dishwasher to normal operation.

The blinking button lights indicate the buttons are bad. The console will have to be replaced.

you'll need to enter a diagnostic mode, press in this order, hi-temp(sani-rinse)----heated dry--hitemp---heated dry... all lights should light, close door and let cycle for about a min, after press the cancelbutton, you should be good to go, the buttons on your model may read slighty different names, if this "toggle of buttons" does not work, you can remove thelower access panel and htere willl be a tech sheet/trouble shoooter behind the panel, in there it will explain how to enter diag/test mode

could be faulty outlet pump

Try holding down "Heated Dry" for about five seconds, until the light switches off. You should be good to go.