Default factory password - Cell Phones

Probably you can access the settings through the operation screen on the machine.
There you may find this reset setting.

I found a manual here:
https://www.sharp.eu/cps/rde/xbcr/documents/documents/om/34_ppc/MXB382-SC_OM_Start-Guide_GB.pdf

There in it says:
Factory default passwords
When accessing the system settings, the administrator password is required to log in with administrator rights. The system settings can be configured in the Web pages as well as on the operation panel. To access the system settings using the Web pages, a password is also required.
Factory default administrator password is “admin”
Store a new administrator password as soon as the machine is installed.
Once the administrator password has been changed, the new password is required to restore the factory default password. Take care to remember the new password.
Factory default passwords (Web pages)
There are two factory default accounts: "Administrator" and "User". A person who logs in as an "Administrator" can configure all settings in the Web pages. In addition, an administrator can restrict access to other settings by enabling "User" accounts.
Default:
users with password users
admin with password admin

If this has been changed when the machine was installed you have a challenge to find out who changed it and if this person still knows it.

Don't need password. Do a factory reset and use the default password...

MOST, if not all, cisco routers have a small recessed button to reset the router to Factory defaults. If you've lost your password, you can hold that button for 30 seconds to reset ALL router settings to factory default. MOST Cisco/Linksys routers use admin/admin for the factory default id/password.

what is the model #?
Most netgear routers default to a username of "admin" and password is either " admin ", "password" or it is just blank. Those are the defaults unless someone changed it.
If you cant get in you can hold down the reset button on the back for 30 seconds (while it is plugged into power) and that will set it back to factory default settings then one of the above should work.
If this was a help please give me 4 thumbs up as I am trying to build up my rep on this site!

this should restore it to default.


By default there is no username or password required to access CentreWare Internet Services. If a username and password have been configured for CentreWare Internet Services and you do not remember the username and / or password, reset the printer to factory defaults (NVRAM reset).
To reset the NVRAM, go to the front panel's Main Menu:

1. Select Troubleshooting, then press the OK button.
2. Select Service Tools, then press the OK button.
3. Select Reset NVRAM, press the OK button.
4. Select Reset NVRAM and Reset Printer NOW, then press the OK button to reset all the settings to their factory default values.

Most of the NETGEAR devices, except ReadyNAS products and Fully Managed switches, have the following default username and password:

• Username = admin
• Password = password
• • For older devices, password = 1234

If you have changed the default password and have forgotten it, you will need to reset the NETGEAR device to factory default settings in order to use the default username and password. Click here to learn how to reset the NETGEAR device to factory default settings. Please note: restoring a device to its factory default settings will erase any changes you have saved to the device.

Hold the Reset Button in, (You have to use a Pen Tip) for at least 5 seconds, that should reset router back to factory defaults.

Restore Factory Default Settings When you restore factory default settings to the base station, you clear your Internet connection settings and any special base station configurations that you have established. After the restore is complete, you will need to reconfigure your base station settings or restore these settings from a backup file. You should restore the original factory default settings only under the following circumstances: O You are experiencing serious problems with your base station, and resetting the base station does not fix the problem. O You cannot remember your base station password. In this situation, you must restore the factory default settings by using the Restore button on the base station, and then use the default password admin to log on to the Base Station Management Tool. To restore factory default settings 1. Open the Base Station Management Tool, and then click Management. 2. On the Management menu, click Back Up and Restore Settings. 3. Under Restore factory default settings, click Restore Factory Default Settings. While the original factory default settings are being restored to the base station, the Power light on the base station turns orange. When the light is solid green, the settings have been restored. If you want to open the Base Station Management Tool after the settings have been restored, type admin as the password on the Logon page. Do not attempt to log on to the base station until the settings are restored and the Power light on the base station is solid green. After you restore the factory default settings to the base station, you should navigate to each page of the Base Station Management Tool and reestablish the network settings you want, or restore the base station settings by using a backup file. For information about creating a backup file of your settings, see the following section. Be sure to establish your unique base station password as soon as possible after restoring the factory default settings to prevent unauthorized users from logging on. For more information, see “Change the Base Station Password.” please rate this answer, thanks

Factory defaults on a 704P is
Username - admin
Password - <blank>

Factory defaults on a 704 are the opposite

This is factory defaults, if someone has reset it, you will need to restore the factory defaults in the router.