My sharp ar5320 has an error code blinking it flashes h 4 what would i do?

E7-10 Shading trouble (Black correction)
The CCD black scan level is abnormal when shading. Improper connection of the CCD unit flat cable CCD unit abnormality MCU PWB abnormality. http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=Sharp&model=AR5320

upon on extra research I've found that this problem was once solved by tightening any loose panels and screws...

Thread Sharp ar5320 error code e7

the error e7 may have a variety of "sub-codes" attached to it, each depicting a different problem. hold the start button down to confirm the subcode. the following site offers the technical explanation of the subcodes: http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=sharp&model=ar5320

that is what you asked for but i think the answer will be too technical when you look it up. but you might then google for a repair of that particular code and subcode and see what appears. for that matter, after you determine the subcode, i see no reason why to not contact the manufacturer's support and report the printer information and error code and see if they have a remedy.

here is a site for downloading a manual for such printers. it might simply be a user manual. http://www.google.com.au/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0cceqfjaa&url=http%3a%2f%2fwww.sharpmea.com%2fcps%2frde%2fxbcr%2fdocuments%2fdocuments%2fom%2f34_ppc%2far5316-5320_om_gb.pdf&ei=csravj7gmuxxmaxsk4hwda&usg=afqjcnedcbf1dnyg_j2h2rxi0ll5sxjrag&bvm=bv.83829542,d.dgy



here is a fellow with a similar problem, an e7 error. but you can see that he was trying to clean the laser and probably disconnected something. http://www.copytechnet.com/forums/sharp/41980-sharp-ar5320-error-code-e7.html?s=84de82058651b6d355c5f09853183f36

good luck.

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. Viewing it in "Mosaic" or "Sidebar" will make surf easy.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.

Put on ur machine & go 2 ur display board & press the C button twice then ur display will go off then input figure 1 & 4 that is 14 then press the print button. if this fails then remove ur fuser unit & check d thermistor, clean any dirt b/w d fuser roller & the thermistor, u can test d thermistor by connecting the two terminal 2 ohms meter

main motor problem

Reset the machine.

The H4 code indicates the fuser may have blown the thermistor. It also could be a false error code. Try this series to clear the error and if it returns, then you'll know for sure the fuser is the culprit. To reset press the following buttons:

1. Press this sequence: CLR-Exposure-CLR-Exposure
2. The display will go blank
3. enter "14", press "PRNT"
4. Press "CLR" several times to exit.

Give that a try and good luck.

There should be two more numbers to that error code. Do you know what they are?

The developer doesn't have a reset code.  It uses a calibration program instead with the reset integrated into it.
Even though the copy quality is fine for now, it can change in the next few days.  You should order some developer.

H4-00 Error Code Sharp AR5320E

Help me please