I have had fault code 10 come up on the machine. Also reads require service

Question edited for clarity - correct name of truck!

Iveco Stralis Fault Codes List ' Truckmanualshub.com

https://truckmanualshub.com > iveco-stralis-fault-codes-...
May 10, 2018 - Iveco Stralis Fault Codes List, diagnostic trouble codes, DTCs, ... 0159 Circuit Malfunction of the fuel pump (high pressure pump)

IVECO Fault Codes DTC - TRUCK Manuals

https://www.truck-manuals.net > iveco-fault-codes
IVECO Truck Fault Codes DTC list. 0111 Malfunction of the vehicle speed sensor circuit. 0112 Sensor Circuit Malfunction 1 pedal acceleration.

Iveco Truck Fault Codes List download

https://www.truck-servicepdf.com > iveco > iveco-fault-...
Iveco Trakker Euro 4-5 Fault Codes List. ... 159 Malfunction of the high-pressure fuel pump circuit. ... 016E The minimum required number of injections is not met.

TRUCK IVECO STRALIS HI-WAY AS EURO 6 [2013-2016 ...

https://www.jaltest.com > coverage > stralis-hi-way-as-e...
Manual diagnostics process of the system through display codes, blinking codes... Allows to read the ECU failure memory by providing the user information about ...

Try simple fix 1st. Remove gas cap and clean it and gas orifice, then reinstall. Then go to auto parts store, borrow meter(free) and read codes.

When the ABS warning (or any other for that matter) comes on a fault code is set in the computer control module, to start diagnosis and testing you need to have that fault code, that requires the ABS system be scanned for fault codes. Right now the ABS system has been disabled until the problem is repaired.

have code read most auto stores offer this service for free the code will assist you on how to repair or service vehicle the computer is advising something is wrong you will need to fix it first --you can reset the computer everyday but if fix is not done it will come back each time

[PDF]Fault Code Bible v1.2 - ResearchGate

www.researchgate.net/publictopics.PublicPostFileLoader.html... ResearchGatesimple, clear instructions on how to read the faults or use the diagnostic routines. .....Resetting the error indication does not rectify the fault but only erases from .... E53 Input circuit EMC errors Displayed as error code, washing machine start ... if you choose position 10, 11 or 12, the test will terminate without pressing.

It is the customer fault code. Simply turn on and turn off appliance.
E11 - problem with fill water
E21 - problem with draining water
E41 - door open
All other errors require service staff !!!

For errors of this type E,2,x, like yours, the manual says to turn the machine off, and remove the power plug from the outlet. About ten minutes later, plug it in again, and turn the machine on. If the problem is not resolved, the machine may require servicing. Please contact your local Service Center.

You can read more about the error codes on Canon website: http://support-au.canon.com.au/contents/AU/EN/8000137001.html

024 360 An error has been detected by the Controller during communications with the Printer. User intervention is required to Power Off/Power On the machine, Field Service is required if the problem persists. Printing is disabled.
http://www.support.xerox.com/go/results.asp?Xtype=docs&prodID=WC7228_WC7235_WC7245&Xlang=en_IN&Xcntry=IND

You will have to either get this printer repaired or replace it.

This sounds like a fuser problem, underheat or over heat. On this machine also, it might be related to NVM, or NVM memory corruption. Sometimes the batteries on the Main Board, they just get old and die.
This can be a multiple problem on the machine.
This might require a Xerox service person to visit the machine.
Some ideas are: A bad heat sensor(Thermistor), very fragil and brittle.
A NVM might need to be reset, Over heat or underheat code in the diagnostice service mode. You need a service manual to find it.Very complicated to explain.
A full sump bottle can cause this, the machine enters a code in the NVM and will keep the machine from "Logicly turning on." Or a broken full sump bottle, sensor falls off or not in place will cause the machine to enter a error code in the NVM.
Good luck.

Fault 10 indicates "No Water is Dispensed."

Solutions =>
– The water tank is not inserted properly. Take it out and reinsert correctly.
– The water tank was not filled correctly during the descaling process. Fill the water tank up to the correct mark.
– After fixing the fault, the machine turns off then on again. Start the desired preparation again.
– If the message still appears contact Technical Service

See page 52 for Fault Codes and Solutions in the owners manual.

http://www.miele.com/manuals_pdf/Residential/Coffee_System/CVA4070_us.pdf