Question about Jacuzzi Balboa R574 System for 1 2 Speed Pump Value 52221 05

2 Answers

Hot tub stuck in 'SL' mode

Water will not get hot, when i turn the jets on its in SL mode. how di i reset it to run and heat..??

Posted by lou_reed on

  • Mike Tebow
    Mike Tebow Jul 23, 2018

    Here's the answer that all experts missed. Sleep mode is ST. After you hit temp and then the light button a temp is on the display. That is where you want it. Standard mode doesn't activate after you see a letter sequence, only temp will show. Most likely 70 degrees. It took over a day to reach 103 degrees because I used hose water. Btw, a tech charged me $260 a week earlier and told me the board and pump were shot. Everything works fine.

  • Mike Daines
    Mike Daines Jul 03, 2020

    Omg thank you....saved me a phone call and service call

×

Ad

2 Answers

Charles East

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 331 Answers

Need to know what buttons your topside control has... depending on the model, some have a mode button which you press and release and then immediately press the temp up or down, to select SL for sleep (no heat), ST for standard (heat as needed) or EC for Economy (only heat during filtration). If the mode button is not present, and you have a single temp button and light button, try pressing and releasing temp and then immediately pressing light button, repeat until choice appears, then wait, it will hold last displayed mode.

Posted on Aug 30, 2010

Ad

Carl Rock

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jacuzzi Master
  • 2,442 Answers

SLeep mode. Exiting sleep is unit specific. A simple way out if sleep mode is to power cycle the unit by turning off power at the disconnect, wait a couple minutes and power back on.

Posted on Jul 03, 2020

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My hot tub is not coming on at all and is giving me a Pr code. What can I do?


please follow this steps and fix it. God bless you
If the unit won't start, make sure power is on at the electrical panel or the electrical panel . Then test the pump and the motor. Check for and repair broken wires or loose or corroded terminals. If necessary, have the pump switch control tested and serviced professionally.
If the jets do not work, clear a blocked water intake of hair and other particles (see below) or replace a broken jet (see below).
If the water in your spa or hot tub is too hot or too cold, check to see if the high-limit reset switch has been tripped and, if needed, reset it. Adjust the thermostat setting and have the thermostat serviced if the problem persists. If necessary, test and replace a faulty heating elements
9d4832d5-8a31-4a17-99b3-af20b93aa530.jpg

Nov 26, 2013 | Qca Spas Dream Series Dream Master Hot Tub...

3 Answers

I am getting a Pr code and the tub is not coming on at all


follow this steps and fix it. God bless you
If the unit won't start, make sure power is on at the electrical outletor the electrical panel Then test the pump and the motor. Check for and repair broken wires or loose or corroded terminals. If necessary, have the pump switch control tested and serviced professionally.
If the jets do not work, clear a blocked water intake of hair and other particles (see below) or replace a broken jet (see below).
If the water in your spa or hot tub is too hot or too cold, check to see if the high-limit reset switch has been tripped and, if needed, reset it. Adjust the thermostat setting and have the thermostat serviced if the problem persists. If necessary, test and replace a faulty heating elements
125a10b3-4403-4cc7-8741-9137c999473e.jpg

Nov 26, 2013 | Qca Spas Dream Series Dream Master Hot Tub...

1 Answer

The instrumentation panel says "SL" and the spa isn't heating.How do I get it to heat again?


You have it in "Sleep" mode. Spa will not heat normally in this mode...

If the SL Message is Alternating with the Water Temp in the Display Screen (we call this "Flashing Sleep"), the Spa is Operating in the Sleep Heating Mode.

If the SL Message is ON Solid (Not Flashing) in the Display window of the panel, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles.

Between Filter Cycles, while in the Economy or Sleep Heating Modes, the Pump has not turned ON and the Last Water Temperature is not Current. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

SL or SLP is one of the Modes you can program your spa into:
EC - Economy
ST/Std - Standard
SL/SLP - Sleep

It is advised you keep your spa in Standard mode. Push the Jets button then immediately push the light button. Each press of the light button will scroll between these three modes.

Good Luck

Aug 27, 2013 | Balboa Instruments Duplex Digital Panel 2...

1 Answer

SL display came on. Not heating.


If the SLP or SL Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Sleep Heating Mode.

If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles.

Hope this helps.
US Parts Center

Aug 31, 2011 | Dream Maker Spas Dream Maker Ez Spa Hot...

1 Answer

I received my brand new ez spa today and once I got the water in and pushed test on the gfci the spa came on and so did the jets. I understand that the motor needs to run to heat the water but does the...


Yes, the jets will run anytime the heater is operational. This is neccessary to keep the plumbing from melting, and also to evenly distribute the heated water. Most hot tubs only take 4-5 hours to heat up, but the easy spa takes very long because they use a very small heating element. Usually only 1.5KW.

Jul 26, 2011 | Dream Maker Spas Dream Maker Ez Spa Hot...

2 Answers

Jet pump will not shutt off after I replaced heater relay. Tub is a hot springs landmark with an IQ2000 panel the year is also a 2000


it sounds like the pump relay may be stuck closed. Also check the temp readout, if it thinks the water is too hot it will try to cool the water by running the jets and sometimes the blower as well.

Dec 08, 2009 | RTO 2 Person Spa Hot Tub 8 Hydrotherapy...

4 Answers

OC hot tub is getting SL error and does not heat. Model is M-09-MOC1545-3. Recently purchased and lost manual. Thanks.


sl means sleep mode and will not heat! try depressing the temp button the either the light button or the jet button usually that will change modes u want st or std mode which means standard. or if u have a mode button try that 1st. or email me a copy of control head to [email protected] for tips! thanks Bob

Oct 17, 2009 | Qca Spas Dream Series Dream Master Hot Tub...

2 Answers

Reset error code hot tub


tub is in sleep mode usually to change u must press temp button then light button you want to b on standard mode STD

Oct 04, 2009 | Qca Spas Dream Series Dream Master Hot Tub...

1 Answer

Pump is running ever 5 minutes. The heat in the


Sounds as if the 'mode' for the tub is set to sense the temperature of the water. see if there is a setting on the control box to a 'timed' setting for filtering and heating instead of controlled by the temperature setting. the problem is the the control box is away from the water and when it calls for heat it is because the water is cooler there than in the hot tub. so when it calls for heat and the water starts to circulate it gets the hot water from the body of the hot tub and then shut down because it senses the 'hot water'. make sense?

Feb 23, 2009 | Blue Wave Aruba 15' Round 54" Resin Pool...

1 Answer

Hot tub will not stay warm


You must keep your circulator pump running if you want the water to stay hot. The water is being heated inside the pipes but it isn't getting circulated until you turn on the jets pump.

Jan 14, 2009 | Heating & Cooling

Not finding what you are looking for?
Jacuzzi Balboa R574 System for 1 2 Speed Pump Value 52221 05 Logo

9,682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

john h

Level 3 Expert

23424 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Jacuzzi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...