Admiral AW22 Top Load Washer Logo

Question about Admiral AW22 Top Load Washer

1 Answer

Hot water connected but does not fill into the drum? The machine will provide us with a cold wash but on the warm and hot settings the hot water dies not pull through the connection

Posted by limehousepro on

Add Your Answer

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 396 Answers

Turn off the water valves which supply the water to washer hoses. Switch the hot and cold water supply hoses and tighten. Turn the water valves back on and try to run a wash cycle using cold. If hot water only is entering the wash tub the water supply is ok. If this is the case you can unplug the washer and turn off the water valves. Remove the washer back cover and follow the water connection for the hot water. The water solenoid valve will have two electrical wires connected to it. Interchange the hot water solenoid wires with the cold water solenoid connection. Connect the water supply hoses hot to hot and cold to cold then plug the unit then test the washer on the cold wash. If the problem persists it could be a water hose restriction or the timer circuit could be defective. If you have hot water at the normal pressure purchase a new hot water solenoid valve. With the electrical cord unplugged be sure to restore the correct wire connections on the hot and cold water solenoid. To replace the hot water solenoid remove the hose clamp and hose to replace the old valve. Connect the unit to the water and electrical outlet. Turn on the water and test the unit for leaks being careful not to touch any electrical and moving parts. If all checks ok and the correct temperature work, unplug the unit and reassemble.

Posted on Jun 21, 2010

  • herman kaase Sep 25, 2013

    I should not have to do this as I purchased this new appliance yesterday.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Wash Machine won't fill with cold water. Makes a electrical buzzing noise when set to Cold/Cold
change water valve
Read full answer
Jan 20, 2016 • Roper RAS8445KQ Top Load Washer
0answers

The water no longer gets cold . What do I check ? Thanks !!
Read full answer
Be the first to answer Jan 13, 2016 • Washing Machines
0helpful
1answer

Hot water fills for very short time on "Warm" setting - wash cycle is too cold
check either ur water temperature switch or and ur water inlet valve with a multi meter for continuity OHMS
Read full answer
Oct 16, 2014 • Amana NTW4650YQ 3.4 cu. ft. Top Load...
0helpful
1answer

EW1200 is rinsing in hot water how do we change that
Hot wash, hot rinse is for 'whites'. Cold wash, cold rinse is for 'colors'. Warm wash, cold or warm rinse is for 'permanent press'. Check your settings to see if you have these options. Double check the hoses, put the machine on cold fill and feel the hoses.
Has someone worked on the machine and possibly put the wires on the solenoids wrong? Easy mistake to make.
Read full answer
Mar 10, 2012 • Electrolux EW1200i Front Load Washer /...
0helpful
1answer

I believe the water temp switch is bad. It will start filling on warm then stop if I put it on hot it will fill with cold water. I have cut the hot water off to achieve this but when it reaches rinse it...
it sounds to me that the hoses are connected to the machine incorrectly. Typically if the plumber ran the water lines behind washer correctly the hot pipe is on the left and the cold pipe is on the right sometimes thats backward and be determined by touching hoses while filling on warm setting and see which hose feels hot. On the back of washer they where they connect hot goes on the bottom and cold on top
Read full answer
Aug 08, 2011 • Estate ETW4400VQ Top Load Washer
1helpful
1answer

Water continues to fill into the washer drum on the spin cycle.
Hi

You could have a stuck solenoid valve
Try this: Set the water temp on cold. Turn on only the hot water.
Does hot water try and fill the drum?
If so then there is a problem with the hot solenoid.

Next set the water on hot. Turn on only the cold water. Does cold water try and fill the drum ?
If so then there is a problem with the cold solenoid.
Read full answer
Jan 05, 2011 • Whirlpool LTE6234D Top Load Stacked...
1helpful
1answer

Washing Machine Rinse and Spin lights are on
its the problem of drum getting blocked by any clothes getting tucked up.also try to move the drum manually with the machine off.if it makes any noise its the faulty motor.or drum has lost its alignment.it needs to be reseated properly in that case. -------------- The water fill valve - The water fill valve is a mechanical and electrical part, the coils on the valve need electricity to mechanically open the valve to allow the water to flow into the washer....myth....the washer pumps water into itself...no, it does not. The fill valve opens and the house water pressure pushes the water into the washing machine.
No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can test a fill valve live for 120 volts, power to a fill valve coil and no fill = a bad fill valve. You can also test the coils for continuity, no continuity = a bad fill valve. Some Maytag washers have a fuse in the fill valve circuit, if this fuse let go the washer will not fill. Fill valves can also from time to time stick open and not stop filling. If you have to shut off the fill valves to stop the water from filling in the washer, you have a bad fill valve and you will have to replace it.
Read full answer
Jul 23, 2009 • Tricity Bendix AW1400W Front Load Washer
0helpful
1answer

No warm or hot water
The easiest possibility is no hot water coming from supply,I have seen the valve turned off,input hose normaly has a filter where it attatches to the machine and they can get clogged.If neither of these solves problem just try hot valve to confirm water supply does work and if so more than likely the valve that hoses are connected to likely source of problem.
Read full answer
Apr 20, 2009 • Kenmore Washing Machines
0helpful
1answer

My whirlpool front load washing machine accept hot water and no cold water entering on the machine.
The water fill valve - The water fill valve is a mechanical and electrical part, the coils on the valve need electricity to mechanically open the valve to allow the water to flow into the washer....myth....the washer pumps water into itself...no, it does not. The fill valve opens and the house water pressure pushes the water into the washing machine.
No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can test a fill valve live for 120 volts, power to a fill valve coil and no fill = a bad fill valve. You can also test the coils for continuity, no continuity = a bad fill valve. Some Maytag washers have a fuse in the fill valve circuit, if this fuse let go the washer will not fill. Fill valves can also from time to time stick open and not stop filling. If you have to shut off the fill valves to stop the water from filling in the washer, you have a bad fill valve and you will have to replace it.
Read full answer
Apr 01, 2009 • Whirlpool GHW9400 Front Load Washer
4helpful
2answers

I have the washer on cold water, but it runs warm, stops, trickles, then comes out warm again, stops, trickles, then warm again ect.On the rinse cycle it will only trickle out.
The water fill valve - The water fill valve is a mechanical and electrical part, the coils on the valve need electricity to mechanically open the valve to allow the water to flow into the washer....myth....the washer pumps water into itself...no, it does not. The fill valve opens and the house water pressure pushes the water into the washing machine.
No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can test a fill valve live for 120 volts, power to a fill valve coil and no fill = a bad fill valve. You can also test the coils for continuity, no continuity = a bad fill valve. Some Maytag washers have a fuse in the fill valve circuit, if this fuse let go the washer will not fill. Fill valves can also from time to time stick open and not stop filling. If you have to shut off the fill valves to stop the water from filling in the washer, you have a bad fill valve and you will have to replace it.
Read full answer
Mar 03, 2009 • Washing Machines
Not finding what you are looking for?

View Most Popular

AW22 Top Load Washer

  • Washing Machines

Related Question

Wash Machine won't fill with cold water. Makes a electrical buzzing noise when set to Cold/Cold

  • Roper RAS8445KQ Top Load Washer

Open Questions:

0answers

Where is the hose filter located on an admiral mega 22 plus top loader The washer won't drain from the rinse cycle and just hums. Trying to find out where the hose filter screen is located to see if it is plugged.
Read full answer
Be the first to answer Nov 09, 2015 • Admiral AW22 Top Load Washer
0answers

Admiral washer won't fully fill with water when set on large load

Read full answer
Be the first to answer Oct 18, 2014 • Admiral AW22 Top Load Washer
0answers

admiral washing machine dose not agitate
Read full answer
Be the first to answer Jun 12, 2014 • Admiral AW22 Top Load Washer
0answers

cannot move inner tub
Read full answer
Be the first to answer May 31, 2014 • Admiral AW22 Top Load Washer

See all Admiral AW22 Top Load Washer Questions

Related Topics

964 views

Ask a Question

Usually answered in minutes!

Popular Questions

How to bypass Lid Switch Admiral Washer

Admiral AAV7000A

Admiral washer won't agitate,drain, or spins

Admiral AW22 Top Load Washer

Washing machine stops at spin cycle and now won't run at all

Admiral AW22 Top Load Washer

Admiral washer will not spin but does agitate.

Admiral AW22 Top Load Washer

Loud noise while agitating in wash cycle

Admiral AAV7000A

Top Admiral Washing Machines Experts

Brad Brown

Level 3 Expert

19166 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Steve

Level 3 Expert

3290 Answers

Are you an Admiral Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...