Question about Whirlpool LGV4634JQ Gas Dryer

1 Answer

Whirpool gas dryer

How to dissconnect blowe fan from motor shaft. I tried clockwise & counter clockwise, but it does not turn, even with a lot of force.

Posted by arshadsuri on

Ad

1 Answer

john gagnon

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 943 Answers

HI thanks for the question. the drum must be out. with a right size wrench. hold the blower wheel . from turning . with a 3/4 inch socket. put socket on the motor pulley. turn the socket clock wise . it should loosen. thanks the appliance doc

Posted on Oct 06, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Which direction does a small motor turn


hi Tristan.
this is what i found.
not sure if its what you are asking.
Which direction does a motor turn? In our simplified diagram, we can say that the wire moving to the left is the equivalent of the motor turning counter-clockwise, and moving right is clockwise. Now, we apply Fleming's left hand rule to determine the direction of the force.30 Dec 2015

Are DC motors reversible? ' Precision Microdrives

https://www.precisionmicrodrives.com/tech-blog/2015/12/30/are-dc-motors-reversible Search for: Which direction does a motor turn?
if this is of no use to you then go to this link and have a look.

Which direction does small motor turn Google Search

Nov 22, 2017 | Cars & Trucks

1 Answer

The light dome on my ceiling fan is stuck and I'm putting a lot of force behind it and it won't budge. I know I'm turning it the right way, I even tried heating it with a blow dryer. Any suggestions...


Depends on what type of fan you have some do get stuck and feel like they are going to break but you can try this trick. As you are turning the globe counter clockwise pess the globe upward and if tht does not work try spraying some magical WD 40 (very little) and see if that works.

Jul 09, 2014 | Dryers

1 Answer

I have a 1 1/2 HP Magnum Force Pump by Jacuzzi. After making some strange grinding noise, I opened it up to find lots of white powdery material flaking off where the Seal Housing (#18) meets the motor...


Thank you for posting your question here on Fixya.com.


Yes, the seal has been leaking and it needs to be replaced; probably the motor bearings too.


Removing the impeller requires you lock the shaft as you turn the impeller off counter-clockwise. To lock the impeller you will have to remove the motor end cover or a cap covering the shaft end depending on which version your particular motor has. Look at the end opposite the pump and imagine a shaft from one end to the other right in the center.


Once you remove the cover you will see a slot for a screwdriver, a flat for a wrench, a hex hole for a hex key or some combination of these. Lock the shaft and spin off the impeller. Some are so tight you will end up breaking them in the process. Simply replace it and the seal. Be sure the motor shaft is in good enough condition to allow the new seal to work properly. If too much shaft material has rotted away the new seal will leak soon after it is installed; you would need a new motor at that point.


If this answer does not fix your problem, please comment with additional details prior to rating the answer. You may also contact me thru our website at www.arrowpools.net. Positive feedback is appreciated once your problem is solved!


John

Apr 08, 2011 | Jacuzzi MAGNUM FORCE POOL PUMP 2 HP...

1 Answer

Fan on outside unit spins counter clockwise pulling air in instead of forcefully blowing air out as it should. This fan doesnot look reversible, could this be the wrong fan or is there a way to reverse it?...


air should be coming out of the top. It will work either way. If your fan is reversible it will have a sticker on the side explaining how to reverse it and it will have exttra wires plugged into each other right at the motor. good luck

Jul 28, 2010 | Goodman CLQ36AR49 Air Conditioner

1 Answer

How do you lock spindle on Delta Osillating sander to change sand rolls?


The spindle screw is reverse tread and you need to turn it clockwise to loosen and counter clockwise to tighten the screw. You can usually hold the spindle with your hand then turn the screw clockwise to loosen the screw. Worst case scenario, carefully turn the machine upside down. Place it on a clean supporting surface. Use a flat-head screwdriver or similar device to remove the plastic gear cover to gain access to socket-head screw. Carefully place the machine on its side. Attach the spindle adapter to the motor shaft turning the spindle adapter counter-clockwise on the shaft.
NOTE: Motor shaft has a left-hand thread.
Place a 7/16" open-end wrench on the flats of spindle adapter. Insert a 3/16" hex
wrench into the socket-head screw located where the plastic gear cover was removed.
Hold the hex wrench to prevent the motor shaft from turning. Turn the wrench counter -clock wise to
fasten the spindle adapter on the motor shaft.
Reinstall the plastic gear cover that was removed above.

Jul 10, 2010 | Garden

1 Answer

We are having issues getting the impeller apart on the jacuzzi magnum force pool pump and need some instructions on how to proceed.


I believe the jacuzzi pump impeller has a locking screw directly in the middle of the impeller. You'll have to turn it clockwise to remove it. Then you'll need to remove the cover from the back of the motor using a 1/4" nut driver. Depending on the motor, you should be able to use a 7/16" open end wrench to hold the motor shaft from turning as you turn the impeller counter-clockwise to remove it. Some motors are different, some have a keyed shaft or require a special tool to hold the shaft while the impeller is removed. Hope this helps.

Nov 22, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

2 Answers

Ac fan not turning on I can ''stick start it'' but which direction?


The condensor fan should be sucking air from the top and blowing it through the coils, probably a counter clockwise direction. The buzzing/humming sound is confusing to me. A humming sound sounds like a motor that can not turn over to start. A starting capacity would be needed. Just because you changed it out last year does not mean it is good. A buzzing sound sounds like a contactor problem. Contactors buzz and after a while, they will fail. In any case, you can "stick start" the condensor fan PROVIDED you are sure the ac compressor is working (this is for a short and temporary use). Also, you may have a high load duty capacitor that assists in the unit running. This will affect your condensor fan operation if it is not good. Unless you know all the components and operations of ac electrical, I would highly recommend calling out a professional.

Jun 26, 2009 | Carrier Heating & Cooling

2 Answers

Cleaning


not sure of the lasko brand but some fans have a cap over the center of the blades that must be unscrewed to remove the blades.( the motor shaft has threads on the end of it ).
some older models actually have the blades that unscrew opposite of turning direction, and you have to find a way to grip the motor shaft and unscrew the blades........
hope this helps.............jay

Mar 20, 2009 | Lasko 1820 Stand (Pedestal) Fan

1 Answer

LGR6611LQ0


you can but now you have to turn the motor shaft at the belt end..i believe you can put your adjustable behind the plastic square blower wheel shaft..on the motor shaft and try turning with your hand its hard to turn because the drum when turning turns the oppsite way,,im,,here onthejob..use gloves

Jan 10, 2009 | Whirlpool LGR6611L Gas Dryer

1 Answer

Hotpoint fan oven motor removal


hi if you have a small blow lamp warm up the shaft and the blade it should after about 5 mins come off also tap it gently with a small hammer try that good luck

Mar 14, 2008 | Ovens

Not finding what you are looking for?
Whirlpool LGV4634JQ Gas Dryer Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...