WHY WONT MY ALARM BEEP

notify viper customer service

Check to see if your vehicle honks when you press the "lock" button on your key fob. Press the "lock" button multiple times in a row. Many devices won't beep unless you double-tap the button after locking. If the horn doesn't honk, but the lights flash, your chirp feature is probably disabled.

Use your keyless fob and ignition key to enable the audible chirp. The process varies considerably on different makes and models. You must usually consult your owner's manual, a dealership or the alarm manufacturer for the correct process.

March 5, 2015.
I'm selling these Zenith Z1233BA Clock Radios
on ebay. I have sold about 10 without any problems, but someone just ask if I know where the get the instructions. I could not find the manual online.
Here are some of the basic.
To set the time set the lock button on the bottom to off, press the clock button, the clock will flash then use the set buttons on top to change the time. Use the <> to change the time, when the time is set press and hold the enter button until you hear a beep. You have to cycle through all the minutes to get to the next hour. Do the same to set the zone. And to set the Date select the CAL button and do the same as setting the time. Put it back on lock when the time, date and zone are set.

To set the Alarm press the Alarm Set button then use the set buttons on top change the Alarm time. Use the <> to change the Alarm time, when the Alarm time is set press and hold enter until you hear a beep. Press the Alarm On/Off button to select radio or buzzer for the alarm or alarm off. To set the PRESETS tune the radio to the station you want to be a PRESET, then press and hold a PRESET button until you hear a beep.

hi Alan

what procedure you are doing for remote matching?
try this one and let me know.

1 Unlock the car, get in and close the door

2 Switch ignition on

3 Press the door lock button on the dash to lock the car

4 Press and hold the door lock button on the dash, the alarm will beep

5 Keep holding the door lock button on the dash, press and hold the lock on the remote,

the alarm will beep

Repeat (5) for the other remotes,

6 leave the door lock button on the dash, the alarm will beep, switch ignition off

A beep tone will activate when selecting the HWS buzzer
alarm.
The alarm beep will become shoter and shoter every
15 seconds for one minute followed by one minute silence
before repeating the cycle.
The HWS alarm will sound for one hour until turning off by
pressing the Power button. Press the Power button whilst
the alarm is activated will cancel the alarm for 24 hours.
1. The HWS buzzer alarm can be set either radio is on or
off.
2. Press and release the HWS buzzer alarm button
, the symbol will flash.
3. During the symbol flashes, long pressing the
button for more than 2 seconds followed by a beep
and display Hour digit will flash.
4. Rotate Tuning Control to select required alarm hour,
then press time set button again. The minute
digit will then flash.
5. Rotate Tuning Control to select required alarm minute,
the press time set button again to complete HWS
buzzer alarm setting.
6. Press and hold down buzzer alarm button for
more than 2 seconds followed by a beep to switch on
or off the HWS buzzer alarm.
Display will appear when buzzer alarm has
been set.

Disconnecting the car battery will reset the alarm system. When you first connect the car battery, the alarm will sound briefly, then stop. You will have to retrain the alarm system to recognize your remotes. The procedure for that varies from one year model to the other. On my 1998 you do it by putting the key in the door lock and holding it full counterclockwise until you hear a brief beep from the alarm horn. Then press a button on your remote and the system will learn to recognize that remote.

Hello, my name is Israel. Your alarm should have an LED light. Check to see if it is on. According to your description, you valet is on. You will need to find a button that is for the alarm, usually located somewhere under the dash. Once you find this button, you will need to turn the ignition to the on position, within 5 seconds, press the valet button once. This should turn off the LED and the alarm should be ready to work again. Good Luck. Please rate.

this seems to be an alarm function. try to do the same again this time press it and hold it in until your beep comes back. good luck.

you need to reset alarm/immobiliser.lock car with remote, hold button down for 30 secs,then press/hold down unlock button,should reset.another way is with key in ignition/turned on, press alarm button down and hold for 30 secs.this resets immobiliser.toyota
systems vary..depending on market.

it may need to be programmed.......

-press the "f" button and hols for 12 seconds (ignore the beep at like 4 seconds.)
-press and hold the unlock button for 2 seconds...the remote should beep two times. each feature that is active will have an led light beside it. press the button to activate the feature. if the light is on the feature is on...

hope it helps...