Question about Symbol LS2208 Handheld

1 Answer

Symbol scanner LS2208

My scanner will not work in the hands-free mode

Posted by rocoleus on

  • Anonymous May 30, 2008

    My scanner will not work in the hands-free mode

×

Ad

1 Answer

Max Quido

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 117 Answers

Hello Roco,
you need the Intelli Stand to activate this function. The scanner can recognize it and activates the Hands-free mode himself. Until you reoved it from the IntelliStand again.

Posted on Dec 05, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Ls2208 manual

HMhmmm ...
I do not have this product in use, but it seem's it detects when it is in the stand and turns to the "constant on mode". If that does not work - I have no idea.
Check out the manual here ...
0helpful
1answer

Disable Sleep Mode

https://portal.motorolasolutions.com/Support/US-EN/Mobile+Networks+RFID+and+BarCode+Scanners/Bar+Code+Scanning/General+Purpose+Scanners/LS2208_US-EN
3helpful
2answers

I have a Symbol LS2208 with an Intelli-Stand and I can't get the hands-free mode to work. I have looked in several places and all I have found is to upgrade the firmware or use an Intelli-Stand. This...

I've found that the magnet in all of the Intellistands at my company (15 stands) is too weak to activate the hands-free operation mode. The quick fix is to attach a stronger magnet to the outside of the stand (with tape or some kind of adhesive). You will see when you bring a strong magnet close to the sides of the scanner that it will begin scanning. adjust the magnet placement attached to the stand for optimum performance.
0helpful
1answer

TO CANCEL HANDS FREE

if this is a new device, there was software sent on a CD. You can use this software to configure your LS2208 and make it so the laser is not on while in the cradle.

If you bought it used, you should be able to download the software from Motorola support website.
0helpful
1answer

Hi can u tell me that symbol scanner ls2208 will work on ATS

The LS2208 is a universal scanner with many supported interfaces. Please check the ATS if one of the interfaces are available. See the list below:
RS-232 IBM 468X/469X Keyboard Wedge Wand Emulation Undecoded Scanner Emulation USB Synapse Adapter
0helpful
1answer

Switching rules Symbol LS2208

Hello Jonathan,
you would need to assign the rules to a specific ruleset. Then you switch between the ruleset to specify which rules are active at the moment. Please see the ADF chapter in the Reference Guide for LS2208 for the barcodes http://support.symbol.com/support/search.do?cmd=displayKC&docType=kc&externalId=5880807apdf
0helpful
1answer

My Symbol scanner sits in a cradle, and the laser goes off and on, rather than remaining on full time. This is a problem, because when I pass a barcode under the unit, I have to wait until it flashes, and...

Yes Symbol LS2208 would be the best... it has an intellistand that enables presentation scanning and easy switching between hands free and hand held models..
2helpful
1answer

How to integrate LS2208 handheld scanner in vb.net

you have to change it to IBM handheld mode and install opos drivers from symbol. then use pos.net to connect to them.
Some computers requires to create some config files to connect through hardware address. It took me like 6 month to figure out but now it works
5helpful
1answer

LS2208

Symbol has confirmed that there was a batch of scanners sent out with defective lasers. Call them at 800-653-5350 for a replacement. Have the scanner handy to give them the serial number. They were very helpful.
2helpful
1answer

Scanner Symbol Ls2208 keyboard not work

The scanner does not detect the keyboard host on power up and is locking up your keyboard. The IBM PC/AT host type barcode must be scanned the first time it is setup. The barcode is on Adobe page 56 of 342 of the LS2208 Product Reference Guide. The scanner should start working immediately after the host type barcode is scanned.
Not finding what you are looking for?
Symbol LS2208 Handheld Logo

929 views

Ask a Question

Usually answered in minutes!

Top Symbol Computers & Internet Experts

Ekse

Level 3 Expert

13435 Answers

Mandeep  Singh
Mandeep Singh

Level 3 Expert

1184 Answers

Vish Iyer
Vish Iyer

Level 2 Expert

76 Answers

Are you a Symbol Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...