Question about Kenmore 63942 Dryer

1 Answer

Replacing broken belt how to get it on is there a sight with step by step pics

Posted by sue_ellen162 on


1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,122 Answers

If you remove the 2 lint screen screws and pull the dryer top toward you and up this will get you in,replaceing a belt is one of the easy repair to make-mike

Posted on May 09, 2010


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do i replacing timing belt?

The tdiclub has a detailed step-by-step with images for this online - I did a search for "ultimate timing belt installation 1.9" and found multiple guides for this.

Nov 16, 2014 | Audi A4 Cars & Trucks

1 Answer

Thump thump noise

A loud rattling/thumping is usually a broken internal roller support rod. You can check by: UNPLUGGING the vacuum, flipping it over, taking the screws out of the roller brush cover plate and removing the plate. It goes back together the same way. If you are nervous about taking it apart, take phone pics step by step as you go so you can see exactly how it came apart for re-assembly. After removing the plate you will see the belt. Pull the roller forward, it will slide out of it's grooves and come out. Slip the roller out of the belt & shake it. It shouldn't rattle, if it's broken inside. Many parts are available at Walmart. If the belt comes off it just slips back on over a metal pin further in the back-you can see it. Use a flat blade screw driver to slip it back on. Slip the new or old one back unside the belt, then back into the grooves till in place. Then the cover & it's screws. You should be back in business!

Sep 04, 2011 | Vacuums

2 Answers

How to replace 2001 hyundai elantra timing belt

Replacing timing belt, requires complete step by step procedure, its not very easy process, but if there is exact procedure, then it gets easy to do this job.For complete step by step procedure with details and diagrams of replacing timing belt of your 2001 hyundai elentra , click this link below :---- -------- This will help.Thanks.Helpmech.

Aug 20, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

Replaced belt and felt stripping now the dryer won't heat. Fault could have happened when the belt broke?

sounds like an electric dryer. with appliance unplugged look for a broken or disconnected may have been knocked out of sight or badly mutilated. be sure appliance is unplugged, before looking for loose connections!

Oct 27, 2009 | GE Dryers

2 Answers

Change cam belt on 1995 legacy

If your going to do or get this done you need to replace the camshaft seals crankshaft seal and water pump plus the idlers and tensioner.
If its a quad cam you might just want to leave it to the pro's........

Jun 26, 2009 | 1995 Subaru Legacy

1 Answer

Changing of belt

Step 1: Lower handle to floor to change belt
Step 2: Remove the two screws from the top hood on the foot
Step 3: Lift hood to remove
Step 4: Lift right end of brushroll (the belt end)
Step 5: Remove and discard belt.
Step 6: Place new belt around motor shaft.
Step 7: Place new belt around brushroll pulley.
Step 8: Align left end cap with base. Push end cap securely into
place. Make sure the square on the brushroll cap is in
Step 9: Pull right side of brushroll to stretch belt. Secure right
end cap into base.
Step 10: Rotate brushroll by hand several full rotations to properly
position belt.
Step 11: Place hood back on cleaner. Replace and tighten
two screws.
Step 12: Return vacuum to upright position.

You can also download your user manual here which has instructions on how with diagrams

Dec 24, 2008 | Eureka Altima Upright Vacuum Model 2996AVS...

1 Answer

Frigidare dryer belt replacment

if your dryer is the one as pictured it is quite a job! I dont feel like writing a bunch of steps that may not even be the right model. Is the pic correct? Ill try to help if it is.

Nov 27, 2008 | Frigidaire GLEQ2152ES Electric Dryer

2 Answers

Dryer won't spin

step 1- remove the face of the dryer, then remove the cover for the fan, check to see if object is blocking the fan, if object is there , remove object, if not go to step 2

step 2- check to see if the belt is broken, if the belt is broken replace the belt.

step 3 - remove the belt from the motor and turn the dryer on, if the motor doesn’t turn then you need to replace the motor.

Jan 01, 2008 | LG DLG5988 Gas Dryer

Not finding what you are looking for?
Kenmore 63942 Dryer Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts


Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides