Question about Hotpoint Ultima WF860 Front Load Washer

1 Answer

F07 Fault code

Last week machine got stuck with one minute to end the washing cycle. I had to re set the machine to wash and spin. This week machine won't wash at all. F07 is flashing after one minute of setting a wash cycle. What should I do. Is this a big problem.

Please help

Posted by michelle_310 on

Ad

1 Answer

Jem

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 212 Answers

Hi I hope this helps....
F07 Fault code - 3_1_2018_9_28_44_am.png

Posted on Mar 01, 2018

Ad

5 Related Answers

douglas smith

  • 1462 Answers

SOURCE: stuck in wash cycle

check if heating by putting on as hot wash and feeling the door. if no heat, check continuity thro the heater - modern heaters have a non-resettable cut-out in them which can cause problems. no heat then no program advance

Posted on May 08, 2007

Ad

Anonymous

  • 209 Answers

SOURCE: HOTPOINT AQUARIUS WF250 1500 SPIN

check the cold water supply, either from the mains pipe, there is no water getting into the machine, if water is there up to the machine check the solenoid for circuit, to do this unplug from electric, remove lid, and test the two wires on relevant solenoid, no circuit means faulty solenoid, (test with the 2 wires removed from solenoid) take care note position of wires to put back properly answer above based on info given

Posted on Sep 27, 2007

prem mathew

  • 1294 Answers

SOURCE: WF860 error code

Click on your model numbers (below FIXYA) on this website, & search. You will get a shortlist; click on your model,below the page u will get Manual/Guides. Click on the blue, you have your manual on line. You might find the mysterious codes there.
And dont forget to rate me on this great site.

Posted on Jan 17, 2008

john mc donald

  • 121 Answers

SOURCE: My washing machine has stopped spinning.

it sound like your belt has come off if not wait till its dark put it on spin turn the light off if you can see flashes coming from under the machine it your brushes that need replaced on the motor

Posted on Mar 03, 2008

Anonymous

  • 185 Answers

SOURCE: Brandt washing machine gets stuck at rinse

check the coupler it might be the timer

Posted on Mar 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GLTF2940ES3 - Frigidaire Front load washing machine e59 error code


http://www.ehow.com/info_12127418_frigidaire-gltf2940fs1-not-spin-error-e59.html

May 02, 2014 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Whirlpool AWO/D 8708


F07 is a fault with the motor control, probably the triac has failed.

Jun 16, 2017 | Washing Machines

2 Answers

Error code f 07 mid cycle?!?


You do not state your machine or model. The error code F07 that I have states that the Central Control Unit has detected a short in the Motor Control Unit.
Check the wire harness between the Drive Motor and the MCU and between the MCU and the CCU.
Check the MCU.
Check the Drive Motor.
Check the entire wire harness.

Replace any defective parts.

Apr 26, 2011 | Washing Machines

1 Answer

End of wash cycle (last 2 minutes,) F code, no spin & drain


If your getting an FdL or F11 (and possibly others) code the problem is more than likely the CCU. The CCU is a circuit board at the inside top back of the machine. The board has quality issues in that it is prone to cold solder joints at the spot where the relays and the spade connectors for external connections meet the circuit board. The repair is to remove the board and touch-up those solder joints.

Jul 06, 2010 | Whirlpool GHW9400 Front Load Washer

1 Answer

Whirlpool awm 8143 doesn't stop at the end of the spin cycle. Instead it clicks for a while when the timer displays 1 minute then displays F07 then goes back to wash cycle. While googling I found something...


F07 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Reconnect power and plug unit in.
Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Replace failed component.

Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 12, 2010 | Whirlpool AWM8123 Front Load Washer

1 Answer

Won't complete wash cycle, stuck at wash after time end!


check heater or thermostat,check is it heat water
if not heat water then heater or thermostat is broken.if you have ohm meter you can check both
,unscrew behind sheet metal and find heater disconnect one wire from it and check it(meter must show some value e.g.30 ohm).

Jul 05, 2009 | Washing Machines

1 Answer

My indesit washing machine is going through the cycle of putting water in turns a few times then says end flashes F07 and sounds like water is pumping in agian and stops??


F07 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Reconnect power and plug unit in.
Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Replace failed component.

Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 30, 2009 | Washing Machines

3 Answers

F07 occurs at end of first rinse cycle


F07 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Reconnect power and plug unit in.
Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Replace failed component.

Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 26, 2009 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Ariston Front Loading Washing Machine error code F07


Error code F07 is indicating that the heater relay is stuck for one reason or another.
This could be a board problem, as this where the relay is located.
However, it would be worth checking that the heater is o/k before you do anything else., as this possibly could cause the relay to malfunction.
Plz rate my solution.
Thanks.

Jan 11, 2009 | Ariston Technologies AW125NA 13 lbs. Load...

1 Answer

Hotpoint WD860 problem


washer wf860 showing f07 error. why

Mar 04, 2008 | Hotpoint Washing Machines

Not finding what you are looking for?
Hotpoint Ultima WF860 Front Load Washer Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

gbob59

Level 3 Expert

3063 Answers

Eric Taylor

Level 3 Expert

590 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...