Question about Linksys RVS4000 Router

1 Answer

How enable multicast traffic on RVS4000? - Linksys RVS4000 Router

Posted by jaderjr2k on

Ad

1 Answer

Harleen Nash

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,768 Answers

1.Your router is set up for multicast automatically
2.Look at the QOS or traffic shaping.

Posted on Apr 21, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does MA5800 support the Multicast?


Yes, it supports Layer 3 multicast networking, also supports IPv4 PIM SSM.

Protocol Independent Multicast-Source-Specific Multicast (PIM-SSM) enables a user host to rapidly join a multicast group if the user knows a multicast source address. PIM-SSM sets up a shortest path tree (SPT) from a multicast source to a multicast group, while PIM-SM uses rendezvous points (RPs) to set rendezvous point trees (RPTs). Therefore, PIM-SSM implements a more rapid join function than PIM-SM.


Different from the any-source multicast (ASM) model, the SSM model does not need to maintain an RP, construct an RPT, or register a multicast source.


The SSM model is based on PIM-SM and IGMPv3. The procedure for setting up a multicast forwarding tree on a PIM-SSM network is similar to the procedure for setting up an SPT on a PIM-SM network. The receiver's DR, which knows the multicast source address, sends Join messages directly to the source so that multicast data streams can be sent to the receiver's designated router (DR).
http://www.thunder-link.com/HUAWEI-MA5800-X7_p928.html

Jan 06, 2017 | Computers & Internet

1 Answer

Multicast


Please open router page and go to advanced just like in this emulator.
http://support.dlink.com/emulators/wbr2310/adv_network.htm

Jul 25, 2014 | D-Link Computers & Internet

1 Answer

Hi, I have two VM citrix servers that i have load balanced using windows NLB. My users are on a different subnet so I have the load balancing configuration set to Multicast mode. (I have a second nic in...


Hello,

I have not worked with 3Com switches only Cisco, but I thought I would post this as I found it when googling:

multicast routing-enable pim
on the vlan interfaces:

interface Vlan-interfacex
ip address ***.***.***.*** ***.***.***.***
igmp enable
pim dm

Those commands should help you get multicasting to work. notice, Vlan-interfacex means you will have to do it for each Vlan you created. Some switches do not include multicast support in their base models but make you buy additional licenses to enable it. Cisco is like that, not sure about 3Com.

Chris

Sep 08, 2011 | 3Com Switch 5500G-EI (3C17261) Network...

1 Answer

Can't stream media to my xbox360 or playstation3?


Hi,
you might need to enable UPNP, or disable a firewall on the internal traffic. Make sure multicast is enabled, and the devices is in the same IP scope.
that all devices have ip´s like:
IP: 192.168.0.??? (where ??? is unique to each device)
Subnet 255.255.255.0 Gateway: 192.168.0.1

Apr 02, 2011 | Linksys Wireless-G WRT54G Router

1 Answer

How can we check whether the switch can support multicast traffic


You need to verify that this switch at least L2 switch if you want to correctly handle this kind of traffic.

Apr 21, 2010 | Dell PowerConnect 6024 24x1000 Mbps...

1 Answer

Network prolem


For
broadcast traffic to use a large portion of your bandwidth you need 2
conditions:

* A very high rate of broadcasts per second
* Large broadcast packets
* Low bandwidth

Aug 13, 2009 | Cisco Catalyst 3560 24-Port Ethernet...

1 Answer

I am trying to telnet through a Linksys RVS4000 from the wan side of the router to a fixed device on the lan side of the router. Both networks wan & lan are operational and I can ping the Wan side...


run netstat on the lan pc to see if telnet server is listening on port 23. look at logs on the router and pc to see if it is blocking any traffic. make sure lan pc has route back to wan

May 14, 2009 | Computers & Internet

1 Answer

I want to setup a wireless network with 3 deskops and atleast 2 laptot


Linksys has a slim Web server built into their routers and a nice little Web based configuration management interface. You can configure your router to pass or filter IP multicast. Most of the Linksys routers have a filter configuration page where you simply check to filter/pass multicast traffic. As for the VoIP/Teleplhony trafic, you should select one of the routers that allows Quality of Service (QoS) - only some routers support this. The QoS router may recognize the voice traffic automatically but at most you would have to specify the applicaation/ports to give priority to. Again, all is done easily via the Web based management utiility - no CLI needed.

Roger

Aug 04, 2008 | Computers & Internet

Not finding what you are looking for?
Linksys RVS4000 Router Logo

Related Topics:

3,098 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Mike

Level 3 Expert

4372 Answers

Brad Brown

Level 3 Expert

18596 Answers

k24674

Level 3 Expert

8092 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...