I was given a videoseven e17ps monitor, but it has no power supply with it. does anyone know which adapter i need. i know it's 19v 2.2A, but i got one and the pin is to small. what am i looking for thanks again guys keith

try lookin on ebay

If the power adapter is a separate from the monitor then check the monitor's label on the back of the screen for the power rating.If the rating on the label is greater than 3.16A then I would not purchase this adapter.
I suggest you purchase an adapter with a current rating greater than what is stated on the monitor's label.
Check out this WEB site for power adapters - a 19Volt 90 watt = 4.7A power supply is suitable.
http://www.cheaperoz.com/z/result.jsp?ga=sc1&q=19v+power+adapter

Looks like it takes a 19V 3.42A Power supply.
Look on the back of the monitor near the power jack and find where it says "input"
If it says 19V 3.42A then this is what you want:

http://cgi.ebay.com/19V-AC-DC-Adapter-Power-Video7-videoseven-L17PS-LCD-/110632100842?pt=LH_DefaultDomain_0&hash=item19c22fe3ea

Yes you'll need a power suppy with following rating: 60Watt 19V 3.16A
you can buy one from here: http://www.chargerbuy.com/replacement-acer-al1913-lcd-monitor-60w-19v-3-16a-ac-adapter.html

Thanks

From my repair experience, 5.5 OD and 2.5 ID is commonly use on the power supply adapter since 2.5mm is made to handle higher current than the 2.1mm (2.1mm is usually for 2A or less).
Center is also positive.
But your can also be 6.5mm OD x 3mm ID. I would try Radi Shack, that is where I get the DC barrel connector in case of emergency repair.

http://lcdpayless.com/productpage.php?productId=4538

http://cgi.ebay.com/19V-AC-DC-power-Adapter-for-Video7-videoseven-L17PS-LCD_W0QQitemZ120609198174QQcategoryZ158844QQcmdZViewItem

Basic LCD monitor and TV troubleshooting guide:
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Hi


in shops with electronics

in case i had help you pls vote me

grigory27419, I wonder why they didn't print or emboss the polarity symbol on or near the place where the plug is inserted into the back of the monitor? I saw a specification that said it requires 19volts dc. But it didn't mention anything about how much current ( 1.5amp, 1.7 amp, 2.1 amp???) it requires. More importantly, why or what caused failure of original "black-brick" supply??? 12fixlouie

Start --> Settings --> Control Panel.
Sounds and Audio Devices.

There is a volume slider here, and should be an option to put an icon in the system tray where you can click to adjust the volume anytime. Make sure you are not muted.

Hi this is the way how to examine what's wrong with your LCD monitors. After you turned it on, you have to check that if you can see the image on the screen or not by shining a flashlight into the screen, not directly but find the best angle to the screen and take a look very closely. If you can see the icons or any image, there will be a minor problem. This is because of the lamps inside screen. Some of them were broken and it is very easy to replace. If you cannot see anything on the screen, there'll be some problems with inverter board. If you have soldering tool and want to fix it by yourself, check the caps first. It may cause this problem. Some caps might show leaking or burning spot on the board because of too high temp. If you don't have soldering tool, you better go get a technician to do so.

Hope this help!! If anything I can help you with, feel free to let me know.
Thank you,

You mean a powersupply cord?Power adapter? If yes have a look at this..
http://cgi.ebay.com/19V-AC-power-adapter-Liquid-Video-A170E101-17-LCD_W0QQitemZ8809242239QQihZ016QQcategoryZ29502QQcmdZViewItem