Question about Toshiba 65H81 65" Rear Projection Television

Mitsubishi 55" Projection TV / Horizontal Wavy Lines at Start Up

Noticing Horizontal Wavy Lines at Start Up on Mitsubishi WS-55513 projection TV. They last about 1 minute and then go away, upon start-up. Is this something a novice can repair and how much does it cost?

bruit Dec 18, 2008

Same exact problem. any solutions? Same exact problem. any solutions?
brian Jun 28, 2013

my tv turns off before 10 sec my tv turns off before 10 sec

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.
Master
1,030 Answers

This is very common with these sets. the fix is to replace 11 very very smal capacitor on what is known as the hypermodule. The ideal sitation is to replace the hypermodule. if you can find it. I can do this repair. I have done about 10 at the shop. if you need to i would suggest finding someone who is very experence in surface mounted repair

Posted on Jan 15, 2009

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Noticing Horizontal Wavy Lines at Start Up on Mitsubishi WS-65315 projection TV. They last about 1 minute and then go away, upon start-up. Is this something I can repair and how much does it cost

convergence ic supply res,Hi ither ic notwworking mamory poparly

Jan 10, 2013 | Toshiba 65H81 65" Rear Projection...

1 Answer

Horizontal wavy lines on picture

Sounds like the convergence has failed. This video gives more details

Apr 12, 2012 | Mitsubishi WS-55513 55" Rear Projection...

1 Answer

Hello, my 55513 tv when turning it on was blurry. after a few minutes it became clear. shut off and came back about 3 hours later and it was blurry again for about 10 minutes. about 10 minutes later it...

in the customer menu select convergence when set acts up---look to see if grid of lines is skewed, see some photos and let me know if your problem anything like this..........

Apr 08, 2012 | Mitsubishi WS-55513 55" Rear Projection...

2 Answers

We got our mitsubishi in 2000. it was working fine and then little by little the picture has wavy lines and you can't see the movie, it has gotten much worse. what can we do?

The wavy lines are caused by the aging of the vertical deflection unit = the defective parts (some capacitors and resistors) must be replaced.
The fix wont be very expensive - the parts will cost less than $25 - but you need a good electronics repair guy to do the job and this is going to cost you.
Remember, it's an old tv that has started to show its age. Maybe it's time to start saving for a new one.

Oct 01, 2010 | Mitsubishi WS-55513 55" Rear Projection...

1 Answer

My Mitsubishi WS-65513 65 in. Rear Projection t.v has a wavy lines in the picture, almost like its a signal problem, but problem follows all the inputs, but goes away after a couple of minutes, what can do...

Bad cap syndrome. Search 'bad cap'

Apr 15, 2010 | Mitsubishi WS-65513 65" Rear Projection...

1 Answer

Have wavy lines in picture sometimes-could this be a faulty wire?

On the signal board there is 4 surface mount transistors. There is one right by the input board (BA09), i would check the corresponding caps and diodes close to it also. I would replace all of the 4 transistors. If this SMT starts to go you will see wavy lines in your picture than it will go away in 3 min or so and get worse over time until no picture is seen. When it totally fails you will have no inputs what soever but you will have an OSD screen and when you choose DTV you will get a scrolling picture.

Nov 07, 2009 | Mitsubishi WS-55513 55" Rear Projection...

1 Answer

Mitsubishi WS-55513 won't power on.

there is an electronic problem inside the tv you shoud go to an authorized service because the power supply to this tv it is in protect mode somehthing hapened inside and need to be repair

Dec 11, 2008 | Mitsubishi WS-55513 55" Rear Projection...

1 Answer

Wavy picture

This EXACT thing just started happening with my WS-48513. Anyone have any ideas?

May 18, 2008 | Mitsubishi WS-55513 55" Rear Projection...

2 Answers

Mitsubishi ws-55513

Could be signal board issue,not related to DM.Might be terminal
board problem = less $ and easier to sub than signal PCB.......T.

Apr 15, 2008 | Mitsubishi WS-55513 55" Rear Projection...

1 Answer

Mitsubishi ws 55513 rear projection HDTV

This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the device and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source) 1. SHUTDOWN AT POWER WITH SELF DIAGNOSIS ERROR 2 2. CHECK FOR LEAKY C9A60 470 PF 1000 V PART # 154P400030, PARALLEL TO D9A57 ON THE POWER PCB. 2. SHUTDOWN AT POWER WITH SELF DIAGNOSIS ERROR 2 2. CHECK FOR OPEN FUSES F9A04 AND F9A05 PART # 283P043090 ON THE +24 AND -24 VOLT LINES. IF THE FUSES ARE OPEN THE CONVERGENCE OUTPUT CIRCUIT WOULD BE SUSPECT

Aug 10, 2007 | Mitsubishi WS-55513 55" Rear Projection...