Bosch Axxis WTL 5410 Electric Dryer Logo

Related Topics:

Posted on Mar 18, 2017
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Bosch 5410 Electric Dryer heat issue The dryer tumbles fine, but the heat turns on for about 30 seconds and then stops. If I stop and start again this scenerio is repeated. I have check out the following: R2- NTC Temperature Sensor, 11K ohms, good R3- NTC Temperature Sensor, 21.5 k ohms, good B9- Overheat Thermostat, good, even jumped out, no change X22- I have 125 volts ac on both lines coming in I cleaned out the lint trap, was blocked up with residue. ------------------------------------------------------------------------------- I have not check out the Temperature regulator below the front door. What am I missing? What else can I check? I'm guessing the power control module is defective, I hope not at ~$270

Answer This Question
  • jake978 Apr 16, 2010

    Any thoughts are helpful.

×

1 Answer

Rich Brown

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Scholar:

An expert who has written 20 answers of more than 400 characters.
Hot-Shot:

An expert who has answered 20 questions.

  • Expert 106 Answers
  • Posted on Mar 18, 2017
Rich Brown
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Scholar:

An expert who has written 20 answers of more than 400 characters.
Hot-Shot:

An expert who has answered 20 questions.

Joined: Jun 10, 2009
Answers
106
Questions
0
Helped
70941
Points
291

There is also another overheat module below the front door too. Check that.
Also, forgive me for asking the very obvious, but have you checked the entire exhaust pipe to make sure that there is no restriction that would cause overheating.

2 Related Answers

Anonymous

  • 213 Answers
  • Posted on Jan 13, 2010

SOURCE: dryer not heating

Common faults -
1 The heating elements can fail (meaning open circuit)
2 There are cut-outs (T.O.C's) that might need resetting
3 The thermostats (stats) can trip out or burn out (meaning opencircuit)
4 Moderntumble dryers also have sensors and pcb's (Printed circuitboards) thesehave programs that can fail and circuitry although most should produce an errorcode showing you were the fault is.
5 Faultyconnections and burned wires may also be the fault.



Free tumble dryer repair videos


We have a Free full video library on appliance repair video’s

Ad

Anonymous

  • 51 Answers
  • Posted on Feb 02, 2010

SOURCE: WTL 5410 BOSCH AXXIS CONDENSATION ELECTRIC DRYER

the thermostats at the element have to be replaced, they burn out prematurely if the condensor unit is not cleaned on a regular basis.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I fix dryer that stopped working?
Check the little button that the door pushes in when you close the door (door switch).
Read full answer
May 01, 2014 • Bosch Axxis WTL 5410 Electric Dryer
1helpful
3answers

Dryer stops tumbling, but heating element stays on
Usually when an electric dryer overheats it's because of a defective cycling thermostat or a clogged vent system. Clean any lint from the internal and external ductwork, and/or replace the cycling thermostat
Read full answer
May 18, 2008 • GE DBXR463EBWW Electric Dryer
0helpful
1answer

I have a Maytag SDE515DAYW dryer. When I turn it on everything works fine for about 30 seconds then it stops heating but everything else still works. If I turn the "extra tumble switch" off...
Does the dryer have a moisture sensor? if it does that may be the problem.
Read full answer
Jul 08, 2017 • Maytag SDE5401AYW Electric Dryer
1helpful
1answer

Hi, My Bosch WTL5410 dryer abruptly stopped. All the lights, including the timer work--as if the dryer was on, but it won't tumble. Even the 'Drying" light is illuminated. I opened the machine up--the...
I have the same issue with my bosch.Did you replace the board?
Read full answer
Feb 11, 2011 • Bosch Axxis WTL 5410 Electric Dryer
0helpful
1answer

Dryer will not stop running
Your machine may have a feature called wrinkle guard or wrinkle shield, which basically keeps tumbling the clothes without heat to prevent wrinkles from setting in. Turn that feature off and see if that does the trick.
Read full answer
May 15, 2010 • Frigidaire Electric Dryer
5helpful
2answers

WTL 5410 BOSCH AXXIS CONDENSATION ELECTRIC DRYER
the thermostats at the element have to be replaced, they burn out prematurely if the condensor unit is not cleaned on a regular basis.
Read full answer
Feb 02, 2010 • Bosch Axxis WTL 5410 Electric Dryer
0helpful
1answer

Re-set button location?
you need to remove the back panel the smaller one that covers heater matrix you will find a thermostat with a red reset button on it when you push it it will click and reset however you should find out why this happened before you use it again as it only does this if it overheats.

hope this helps
Read full answer
Jun 29, 2009 • Bosch Axxis WTL 5410 Electric Dryer
1helpful
2answers

Dryer tumbles but not heat
here is the link for the wiring diagram... heat is definatly on a separate circuit.

http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5174194
Read full answer
May 25, 2009 • Maytag MDE308DAYW Electric Dryer
0helpful
1answer

Bosch Axxis WTL5410 condensation dryer does not heat up
Common faults -
1 The heating elements can fail (meaning open circuit)
2 There are cut-outs (T.O.C's) that might need resetting
3 The thermostats (stats) can trip out or burn out (meaning opencircuit)
4 Moderntumble dryers also have sensors and pcb's (Printed circuitboards) thesehave programs that can fail and circuitry although most should produce an errorcode showing you were the fault is.
5 Faultyconnections and burned wires may also be the fault.



Free tumble dryer repair videos


We have a Free full video library on appliance repair video’s
Read full answer
May 03, 2009 • Bosch Axxis WTL 5410 Electric Dryer
10helpful
5answers

Bosch nexxt 500 series dryer
I just had the same problem, motor runs but no heat. I had a fun time figuring out how take the front panel off, hint the rubber seal comes off easily. It looks like mine tripped the resettable over heat sensor. So far so good.
Read full answer
Jul 30, 2007 • Bosch Nexxt WTMC 3300 Electric Dryer
Not finding what you are looking for?

View Most Popular

Axxis WTL 5410 Electric Dryer

  • Dryers

Related Question

How do I fix dryer that stopped working?

  • Bosch Axxis WTL 5410 Electric Dryer

Related Topics

149 views

Ask a Question

Usually answered in minutes!

Popular Questions

Bosch Dryer lint filer warning

Bosch WTMC3510UC Gas Dryer

I have a two year

Bosch Dryers

Water tank full (!) in bosch tumble dryer WTE86301gr

Bosch Dryers

Bosch Nexxt 500 Electric Dryer: lint filter light goes on even though it does not need emptying

Bosch Nexxt WTMC 3300 Electric Dryer

My BOSCH dryer #WTE86300US keeps stopping in mid

Bosch WTE86300 Electric Dryer

Top Bosch Dryers Experts

vince

Level 3 Expert

2530 Answers

Cindy Wells

Level 3 Expert

6688 Answers

NOEL
NOEL

Level 3 Expert

8606 Answers

Are you a Bosch Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Bosch WTL 5410 Dryer.pdf....

Axxis WTL 5410...

PDF Manual
. Axxis WTL 5410 Electric Dryer Manual

Axxis WTL 5410...

Loading...