Washing Machines Logo

Related Topics:

Question about Washing Machines

1 Answer

Our washer works fine until the spin cycle. The drum spins and the agitator spins until the end of the spin cyle. At this point the drum spins, but the agitator stops spinning and there is a knocking noise. HELP!

Posted by c w on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 21 Answers

Open the washer in the back and check the drum+agitator.

Posted on Apr 05, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Washer doesnt spin

as you said it does rest of cyle well. then the only problem can be faulty timer. may be in spin part of timer contacts are not getting on.
0helpful
1answer

Drum won't spin, drains ok and agitator works fine

http://www.pcappliancerepair.com/model-display.php This site shows your lid switch. Just enter your model number. The lid switch is the usual suspect for your symptom.
1helpful
1answer

Maytag washer will not agitate. model pavt244aww

TURN THE PULLEY ON THE BOTTOM. ONE DIRECTION WILL CAUSE THE PULLEY TO TRAVEL UP AND RELEASE THE BRAKE, CAUSING THE TUB TO SPIN. TURN IT THE OTHER WAY AND THAT SHOULD BE YOUR AGITATION. YOU SHOULD HEAR THE TRANSMISSION CLUNK AS THE GEARING CHANGES DIRECTION TO GE THE AGITATION ARC. IF NO NOISE IS HEARD, YOU HAVE AN INTERNAL PROBLEM WITH THE TRANSMISSION.
0helpful
1answer

Noise when stopping after spin cycle or open lid (after moving)

check hub nut, it is likely loose, its under the agitator. top pops off agitator and bolt hold agitator down.
0helpful
1answer

While in spin cycle agitator spins, but tub does not

Hello, it is the drum shaft collar or what the tub rests on. It is on the top of the shaft. You need to remove the shell, the plastic collar that rests on top of the drum, the agitator, then the nut that holds the drum down, and then pull the drum out, and then you will see the collar. I know it is hard to get to so I would call a pro for this job unless you think you can do it. The part is cheep it is the labor that will cost you. Thank you
3helpful
3answers

Whirlpool super capacity Lsq9549lw0 has trouble spinning on its own.

If the washer does fine thru the agitation cycle (the washing), that means the motor is OK and the coupler is OK.  It would not agitate unless both are OK.  (and don't listen if anyone tells you the lid switch is bad -- machine would not fill & go thru wash cyle). The spin is another matter.  There is a separate tube for spinning the basket.  There is a drive  block at top of the tube (that sometimes fails)  and there is a separate cluch mechanism below, under the tub.  Those places is where you should look.
2helpful
2answers

Roper(whirlpool) washer will not spin model # ras7133kq1

check the motor coupler between the motor and the transmission
0helpful
2answers
0helpful
1answer

Mav7200-57-58

The timer itself is bad, replace and wala! Timer Part Number: PT756240 Made by MAYTAG http://www.partstap.com/partsearch/model.aspx?model_id=47859 $70.22 + S&H
0helpful
4answers

Washer will not pass wash cycle...Will not Drain

Nightshade, in most cases, no spin, no drain is a lid switch problem. If you advance the timer to the spin position does it spin? If the machine is agitating you can rule out the coupler. If you are sure that it is not a lid switch problem, then you are probably looking at a bad timer....Catriver..post back.
Not finding what you are looking for?

365 views

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Brad Brown

Level 3 Expert

19166 Answers

W.L.

Level 3 Expert

2511 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...