Question about Viper Security and Remote Start System (basic install included)

1 Answer

Trying to program 474v remote for viper car starter

Posted by Anonymous on

  • Anonymous Apr 12, 2010

    I did not report this as an abuse. I reported that his 'fix' didn't work.....huge difference. Please adjust! Thank you!

×

Ad

1 Answer

alex

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

Super easy
1. Make sure car is disarmed
2. Get in car turn key to IGN position
3. Push valet button one time and let go
4. Push and hold valet button.
5. While holding button push either lock or unlock on keypad of new remote.
6. Siren or horn should sound.
7. Let go of valet button and turn key OFF
8. Test remote
9. Smile and grab a shake ;)

Posted on Apr 04, 2010

  • Otis Bryant Nov 21, 2011

    I just get a remote and i did the same thing but just the lock button works only. The unlock button dose not work and the remote start dose not work.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a viper 160xv remote starter sys ane my remote 474v 4 button only starts my car need to program it to lock and unlock it


I checked around to see what i could find out about these systems and while they seem to be one of the better ones, the one thing i keep seeing no matter which system i look at is the following words....Installation to be done by a professional installer only.

This usually means you have to take it back to where ever you had it installed and have them "PAIR" the keyfob and the system again or to activate new or "LOST'" features.

Sorry i can't be more help but that's all i could find out about the systems. Sorry

Dec 22, 2011 | Viper Security and Remote Start System...

1 Answer

Remotes won't program! Installed Viper 5001 on my 2007 Kia Sorento. Triple checked wiring..all is good. Remotes won't program...no power to main unit. Yet, tested main unit and it has power. Any...


There are two constant 12 volt wires at the ignition on this vehicle: blue and green. The red power (with fuses) wires from the Viper should be connected to either of the two. The ignition wire is yellow. The pink wire from the Viper should be connected there. The accessories are orange and white. The pink with white from the Viper should connected to one and the orange from the Viper should be connected to the other. Please note that the Pink with white should be programmed to act as an accessory (off during crank). The starter wire is red and the purple from the Viper should be connected there. Also check for a good ground connection.

For programming:
Press and hold "f" until LED lights solid (approximately 10 seconds), then press and hold remote starter button(circle w/arrow) until LED blinks three times and the amber transmit LED lights up.
Now you have to enter the remote control learn routine: Turn ignition on, within ten seconds press and release control button on antenna then, press and hold control button while pressing the lock button on remote. System will respond (horn/chirp/flashing parking lights) when holding control button and when pressing lock button on remote.

Jan 17, 2011 | 5101 LE 1 Way Car Remote Starter System

1 Answer

I bought a 2007 Camry with a remote start. The seller doesn't know how to start the car with the remote. The remote is a 4 button Viper 474V.


First, be sure that the remote is programmed for the vehicle by using it to operate the door locks(pressing the lock and unlock buttons). The parking lights should flash if nothing else works.The usual way to operate the remote starter with this remote is by pressing the * button once but, the option could have changed if the remote has been reprogrammed differently. So, try pressing the * button once. If this doesn't work press it twice within two seconds.If this doesn't work try pressing the lock and unlock buttons at the same time. If these steps fail to initiate the remote starter try the steps listed for the * button with the aux button. If either of the remote starter inhibits (hood pin, neutral safety) are active you should receive flashing parking lights for a failed attempt to remote start.

Jan 16, 2011 | Remote Start System

1 Answer

Viper rpn 474v 288 codes manual


You should be able to find what you need here. If your alarm isnt listed, give them a call. They have great customer support. Hope this helps. : )

Jan 10, 2011 | Viper Security and Remote Start System...

1 Answer

Remote car starter worked last week but this week it won't start. Changed battery in the remote and still won't start. It will unlock and lock the doors but just won't start.


It probably needs to be re-programed
I have a viper model 5101 and this is how you program it Hope it helps !



Programming the Viper Remote Starter 5101


Unlock the doors before starting


Push and hold f button for 8-10 seconds until amber light is on solid


Push Remote start button for about 4 seconds till amber light flashes 3 times


Put key in IGN to the on position but don

Jan 05, 2011 | Remote Start System

1 Answer

I need instructions on how to use my viper 5101 remorte starter


go to www.directed.com this is the manufacturer of the viper remote starters, there you should be able to download instructions.

Here is how you program the viper 5101 remote.



Programming the Viper Remote Starter 5101


Unlock the doors before starting


Push and hold f button for 8-10 seconds until amber light is on solid


Push Remote start button for about 4 seconds till amber light flashes 3 times


Put key in IGN to the on position but don

Dec 30, 2010 | 5101 LE 1 Way Car Remote Starter System

1 Answer

I lost my viper remote starter, i already bought a replacement remote, but how do i progam it? I have the basic five button remote, black buttons and silver borders around the whole remote.




Programming the Viper Remote Starter 5101


Unlock the doors before starting


Push and hold f button for 8-10 seconds until amber light is on solid


Push Remote start button for about 4 seconds till amber light flashes 3 times


Put key in IGN to the on position but don

Dec 12, 2010 | 5101 LE 1 Way Car Remote Starter System

1 Answer

Program a remote starter key faub a 474v


turn ignition on and press valet button and release. then press and hold the valet button. it will toot or chirp once. press the lock button on the transmitter and it will toot or chirp one more time. shut off key and one more toot. the go ahead and test the remote

Feb 05, 2010 | Viper Vehicle Parts & Accessories

Not finding what you are looking for?

Open Questions:

0 Answers

Viper 4806v won't program I am trying to install a viper 4806v two-way remote start/keyless entry in my automatic 2004 toyota camry LE 4cyl. I got the lock/unlock, horn, lights to work, and trunk pop to work. I can't seem to get the remote start to work. When I press the remote start button on the remote keypad, the car does not start and the headlights flash 7 times. Troubleshooting says 7 flashes mean a manual transmission mode error. This means I have to enter programming menu 3 and change the starter to automatic mode. When I follow the directions to get to menu 3, nothing happens because I cannot get to menu 3 when I hold down the control button after turning the ignition off. In other words, the control button is not working. The neutral switch is on like it is supposed to be. Kind of bummed about this. Could use some guidance. My wiring goes accordingly and this car does not have an immobilizer because I used a regular metal key to start it. This car has no alarm, just a stock keyless entry, trunk release, and panic button. Again, the problem is :The remote start comes in default manual transmission mode so I have to switch it to automatic transmission mode but I can't seem to enter programming. When I try to enter programming with the procedure followed using the control button, nothing happens. It does not chirp and the LED does not blink. I also cannot enter valet mode using the control button. When the car is locked, the LED blinks and stop blinking if car is unlocked ignition is turned on. I do not understand what is going on. VIPER 4806V Wires --->Camry Wires Main Harness 6pin connector H1/1 Red 12volt input (+) --> (+) White/Red at ignition Harness H1/2 Black Chassis Ground (-) --> Car Frame (-) H1/3 Brown 200mA Horn Output (-) --> Green/Black (-) at steering column H1/4 White/Brown Light Flash Isolation Wire --> NOT USED H1/5 White Light Flash --> Hazard Light Flash Relay Lt. Green Black wire (-) H1/6 Orange Ground when armed --> NOT USED Door Lock 3 pin connector 1 Blue 500mA Unlock Output (-) --> Blue Wire (-) white connector at driver kick panel 2 Empty --> NOT USED 3 Green 500mA Lock Output (-) --> Blue/Yellow wire (-) blue connector at driver kick panel Auxillary/Harness 24 Pin Connector 1 Pink/white 200mA Ignition 2 output/ Flex output (not used) --> NOT USED 2 Blue/White 2nd Status/Rear defogger output (-) --> NOT USED 3 Red/White 200mA Trunk Release Output (-) --> 5pin Relay Pin 85 (86 & 87 to +12V, 87a White/blue trunk wire toward dash, 30 white/blue trunk wire toward trunk) 4 Black/yellow 200mA Dome light Output (-) --> NOT USED 5 Dark Blue 200mA Status Output (-) ---> NOT USED 6 White/Black 200mA Aux 3 Output (-) ---> NOT USED 7 White/Violet 200mA Aux 1 Output (-) ---> NOT USED 8 Orange/Black 200mA Aux 4 Output (-) --> NOT USED 9 Gray Hood Pin input (-) ---> Installed at hood and Switch is open when hood is closed 10 Blue Horn input (Jumper set (-)) --> Green/Black (-) at steering column 11 White/Blue Activation Input --> NOT USED 12 Violet/White Tachometer Input --> Black/Orange wire on the Datalink Connector 13 Black Neutral safety/Parking Brake Input (-) ---> (-) Ground to metal frame of car. 14 Green/Black 200mA Factory Alarm Disarm Output --> NOT USED 15 Green Door Input (-) --> Red/Black Wire (-) (Door open indicator on dashboard) 16 Empty --> NOT USED 17 Pink 200mA Ignition 1 Output (-) --> NOT USED 18 Violet Door Input (+) ---> NOT USED 19 Violet/Black 200mA Aux 2 Output --> NOT USED 20 Brown Brake Shutdown input (+) --> Green/White Wire (+) at brake switch above brake pedal 21 Violet/yellow 200mA Starter Output (-) ---> 5 pin Relay pin 85 (Pin 86 & 87 is +12volts, Pin 30 black/yellow starter wire (+) at pin 8 in ignition harness) 22 Gray/Black Diesel wait to start Input (-) --> NOT USED 23 Orange 200mA Accessory Output (-) --> NOT USED 24 Green/White 200mA Factory Alarm arm output (-) --> NOT USED Remote start 8 pin Connector 1 Red/black 12v Constant Input for Acc and starter relay (+) ---> White/Red wire 12v (+) at ignition harness 2 Pink/black Flex relay input 87A key side (+) --> NOT USED 3 Pink/white Ignition 2/ Flex Relay output (+) --> Black/yellow pin 4 at ignition harness 4 Red 12V constant input for ignition 1 Relay (+) -->White/Red wire 12v (+) at ignition harness 5 Violet Starter Output (+) --> Black/White wire (+) at ignition harness 6 Accessory Output (+) --> Blue/Red (+) at ignition harness 7 12v Constant input for ignition 2 and flex relay (+) ---> White/Red wire 12v (+) at ignition harness 8 Pink Ignition 1 input/output (+) --> Black/Red wire (+) at ignition harness.

Oct 20, 2014 | Viper Security and Remote Start System...

See all Viper Security and Remote Start System (basic Questions

Viper Security and Remote Start System (basic install included) Logo

6,133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Viper Home Security Experts

Brad Brown

Level 3 Expert

18564 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

61177 Answers

Are you a Viper Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...