Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

On/off rinse hold & TIME SAVER LIGHTS FLASHING WON'T DO CYCLE

Posted by djtdavytyrer on

Ad

1 Answer

Dave Smith

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 86 Answers

For error code definitions on Hotpoint, Creda and Indesit machines use this link

Posted on Mar 18, 2010

Ad

1 Related Answer

Dave Smith

  • 86 Answers

SOURCE: error codes On/off rinse hold

For error codes and what they mean go to www.selfix-uk.co.uk

Posted on Jul 23, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine stuck in drain mode, beeps, can only turn off at powerpoint.


Your motor controller board is faulty
needs repair or new/recondition board.

May 06, 2013 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Error code e01


do the following steps: God bless you
To start test program, press and hold both POWER SCRUB PLUS and RINSE & HOLD program buttons, then turn unit on by pressing ON/OFF button. When program buttons are released, lights above them will flash. To end test program, press ON/OFF button.To check program indicator lights (POWER SCRUB PLUS, REGULAR WASH and RINSE & HOLD), press and hold each program button. When REGULAR WASH program button is pressed, CLEAN light also comes on.
To start testing, press both POWER SCRUB PLUS and RINSE & HOLD buttons a second time. When testing has ended and a fault was detected, the following indicator lights will be lit:
POWER SCRUB PLUS = Heater fault
REGULAR WASH = Water filling fault (over or under filling)
RINSE & HOLD = NTC (temperature sensor) fault ? note circulation motor stops shortly after it started during an NTC fault
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), REGULAR WASH light will come on and unit will continually fill and drain where testing won't be completed. If flow switch (e5) has failed (opened), water won't heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), RINSE & HOLD light will come on immediately and testing will end shortly after water has started circulating.
If more than one fault occurs, more than one light will be lit.

Jul 21, 2012 | Dishwashers

1 Answer

Error codes On/off rinse hold & TIME SAVER LIGHTS FLASHING


For error codes and what they mean go to www.selfix-uk.co.uk

Jul 21, 2011 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

What does the 'eco option' on the MW512NZ model actually mean?? Cheers


Eco is a water saver option, using less water on the rinse cycle. It saves 25% more water than the water saver option on the rinse cycle (if available, depending on model). Eco and water saver cannot be used with fabric softener. Eco and water saver are slower than the regular rinse cycle.

Smartdrive User Manual

Dec 20, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Hoover visionHD vhd 842-80 will not complete its cycle (does not spin) lights flashing are 1200 &time saver button


Mine done the exact same thing and it was the bushes that went not the pump, so you can change them your self if you can

Nov 07, 2010 | Hoover Washing Machines

1 Answer

Year old Bosch SHU33A0UC won't start. Lights on


Light's on mean you have power.

Initiate the self test program by doing the following -

To start test program, press and hold both POWER SCRUB PLUS and RINSE & HOLD program buttons, then turn unit on
by pressing ON/OFF button. When program buttons are released, lights above them will flash. To end test program, press
ON/OFF button.
To check program indicator lights (POWER SCRUB PLUS, REGULAR WASH and RINSE & HOLD), press and hold each
program button. When REGULAR WASH program button is pressed, CLEAN light also comes on.
To start testing, press both POWER SCRUB PLUS and RINSE & HOLD buttons a second time. When testing has ended
and a fault was detected, the following indicator lights will be lit:
POWER SCRUB PLUS = Heater fault
REGULAR WASH = Water filling fault (over or under filling)
RINSE & HOLD = NTC (temperature sensor) fault – note circulation motor stops shortly after it started
during an NTC fault
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil,
measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays
at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), REGULAR WASH light will come on and unit will continually fill and drain
where testing won't be completed. If flow switch (e5) has failed (opened), water won't heat (to 150ºF) and water won’t stop
circulating. If NTC probe (f2/f4) has failed (opened), RINSE & HOLD light will come on immediately and testing will end
shortly after water has started circulating.
If more than one fault occurs, more than one light will be lit.

Let me know what you figure out. I can repair these boards most of the time.

Dec 18, 2009 | Bosch 24 in. SHE44C02UC / SHE44C06UC /...

1 Answer

Hotpoint WF430 lights flashing will not start


Hi, the problem is the pump is blocked. What you have to do if your a bit handy is to turn off the power from the plug socket, pull out the machine and take off the back panel, then when you look iside you will see a big black rubber fitting at the base of the mashine attached to a white plastic pump and inturn to your outlet pipe. you have to disconnect the big black one from the top, there is a metal clip which you have to unscrew and it will fall down. inside this is a plastic ball and something which looks like a shuttle ****, take this out and clean everything, you will be suprised what is in there (especially if you have kids) lastly put everything back together and put on a quick rinse cycle. all is fixed! OR Call an repair man, who may try to con you into new parts when they are not neccesary.

Jun 05, 2009 | Hotpoint WF430 Front Load Washer

1 Answer

Hotpoint washer dryer lights flashing


Check first the thermal fuse.

Test heating element to ensure is not grounded, and staying always on. Test the fan and ventilation system.

If you find no fault in there , then test the timer control board.

Enter the model number on one of two websites below to get parts and diagrams for your appliance:


Appliance Parts From PartSelect

Appliance Parts Pros

Apr 23, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...

4 Answers

Green clean light flashing dishwasher


press back and forth between hi-tempwash and sani rinse several times to get all lights to come on if not then press sani rinse and heated dry back and forth several times. one of though combos will start the test mode

Nov 22, 2007 | Dishwashers

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

574 views

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

gbob59

Level 3 Expert

3063 Answers

Cindy Wells

Level 3 Expert

6259 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...