Question about Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Maytag 24 in. MDB7600A Jetclean -- the door hinge is bent down (a grandchild stood on it) so the bottom wire tray does not roll in easily. How can I make the door stop at 90 degrees?

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

New Friend:

An expert that has 1 follower.
Expert
44 Answers

Only solution is to replace the door hinges

Posted on Mar 17, 2010

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Dishwasher leaks like a seive! water runs out of the bottom of the door and from under the control panel! help, it's ruining my basement ceiling!

Hi,

Here is a tip that I wrote about dishwashers and them leaking.

Leaking Dishwasher

heatman101

Sep 14, 2010 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

Model MDB7100AWW. Machine washes okay but does not dry dishes. Element tested as okay. No drainage problem. Is there a thermostat that should be replaced?

You have to verify that element is actually receiving voltage at start of dry cycle. Cause will be timer or relay. Be sure to check hi-limit switch and door seal.

Aug 19, 2010 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

Someone suggested replacing the hinge.

hinge is operated by springs that connect to the base of the unit where the adjustment legs are. The tension on thew door can be adjusted by moving the spring to the next hole on the base. Remove bottom panel of the unit at the floor area and look under the unit you will see the spring and the holes on the base frame that they hook to. Move the spring back for more tension and forward for less.

Hope this helped
Dave

Mar 17, 2010 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

Fisher and Paykel dishwasher

Ok Im going on the Maytag Model # MDB7600AWB your model is missing some at the end.

If this is your Model the your door cable most likley has broken. part # 99003446

Please verify your model # from your machine looking around the door frame.

Jan 10, 2010 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

Quietseries 300 : Fills OK, timer functions OK, no water movement

Check the Lid switch. Most top load machines will not spin unless the lid is down and this is determined by the lid switch.

Jan 07, 2010 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

How do you safely replace the handle on this MDB7600A dishwasher

Easy job. You'll need a new "latch assembly". I found one at appliancepartspros.com for $18+ and $7 shipping. Part #W10130695. More $ elsewhere. Procedure: Remove torx head screws on 3 sides of the door, then pull the interior part of the door away from the exterior a few inches at the top of the door. The old latch assembly (and the broken handle, now separate) can now be accessed easily. There are two wire connectors press fit to the latch assembly switches. Use a screwdriver if necessary to pry them off the old assembly, which is probably corroded somewhat. Do this one at a time and replace on the corresponding terminals of the new latch assembly so the wires don't get switched (or else mark them before removal.) Reposition the latch assembly, push the two halves of the door back together and replace the screws. Done. I'll note that the latch is positioned but not secured by two pairs of thin plastic "fingers" molded into the back of the control panel. Three of four fingers had sheared off. I didn't feel like spending $70 to $130 for a new control panel so decided to try doing without. The latch is secured by the two center screws at the top of the door, so as long as those are tight it should be fine.

Jan 02, 2010 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

Why my maytag dishwasher super capacity plus 2 does not drain

what does it not do or do

May 02, 2009 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

I have residue on dishes with a maytag mdb7600

clean out the food trap in the bottom inside of the dishwasher. Also your water may not be hot enough...either select hot wash or increase your hot water heater temp.

Mar 24, 2009 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer

Maytag dishwasher heavy door (broken door spring(s))?

Hi thanks for the question. to repair . bottom kick plate must be removed ,to get to the door springs .4 screws . remove them. springs on each side . replace them thanks the appliance doc.

Oct 06, 2008 | Maytag 24 in. MDB7600A Jetclean® II...

1 Answer