NRS Cascade Brix single hole lavatory faucet with 1-1/4" pop up waste 47360S-65 Logo

Question about NRS Cascade Brix single hole lavatory faucet with 1-1/4" pop up waste 47360S-65

1 Answer

My daughter pushed down on the plug & now it doesnt pop up!! lever at back doesnt work as the suction is so good!

Posted by shellsean6 on

Add Your Answer

1 Answer

Brandon Roberts

  • Level 1:

    An expert who has achieved level 1.
    New Friend:

    An expert that has 1 follower.
    Corporal:

    An expert that has over 10 points.
    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 17 Answers

Drain assembly can be taken apart from under the lav. first loosen the stopper lever assembly. then proceed to loosening up the slip-nut on piping nearest to the drain. The drain is held to bottom of sink by a nut tightened to a thick rubber washer. Remove nut and remove drain. Dislodge stopper. Replace drain with fresh plumbers putty, underneath lip of drain where it makes contact with inside of lav. Reassemble drain piping and lever.

Posted on Mar 17, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a hitachi nv45...aand dropped it of the roof.It broke the pushing lever (part #888-883)I replaced it and now the gun isnt firing properly.The guns rapid fire doesnt work.You have to push the trigger...
Sometimes after a good knock on the side the cylinder will bind and not work correctly. Remove the head and make sure that the cylinder moves easily up and down. If cylinder is ok, then most likely the adjustment on the pushing lever set too low. New pushing lever does not come with the adjustment screw and lock nut. Adjust the screw up or down for best firing position. If the adjustment screw is in place and adjusted, make sure that the plunger is not sticking within the valve(plunger makes contact with the adjustment screw on the pushing lever). With pushing lever removed, the plunger should move easily in and out. Good luck
Read full answer
Oct 13, 2014 • Air Tools & Compressors
0helpful
1answer

1991 isuzu pickup hood opening problems
I have had a few vehicles do that over the years, check the cable for any kinks, if you find one thats bad enough you may need to replace the hood release cable. If no knks are found just lube it up with WD-40, do the entire hood release system, that always worked on mine & one time one of my dumb friends turned a hood alignement stop (on both front corners) & put pressure on my hood so it wouldent pop up unless someone pushed down on it while I pulled the release handle.
Read full answer
Nov 23, 2012 • 1991 Isuzu Pickup
0helpful
1answer

I need instructions on how to mount the nuvi 200w to my windshield
To secure the nuvi 200w to your windshield with the included suction cup mount (pictured below),


steve_con_6.jpeg

center the GPS on the clip, and tip the bottom edge on the bracket. Push the top of the GPS against the top clip until it clicks into place. Hold the bracket and GPS near the windshield where you like it best. Note where the suction cup is on the windshield in relation to the mirror, etc. Remove the GPS from the mount's clip by pushing the top tab back from the top of the GPS.

Clean the windshield (or portion that the suction cup will be stuck against) with a paper towel or newspaper and ammonia solution like Windex, etc. Clean the suction cup with the paper towel and Windex, too.

Lift the lever at the base of the mount - is shown in the picture above - if it isn't already. With the mount oriented as shown in the picture above, press the suction cup against the windshield where desired with one hand. Hold the mount firmly against the glass and use your other hand to press the lever on the base back toward the suction cup and glass. Press until it lays flat against the base / suction cup. Plug the power cord into the GPS and reinstall the GPS in the mount clips as done earlier.

To remove from the windshield, release the GPS from the mount clips, and lift the lever away from the base / suction cup. Locate the tab that is connected to the suction cup edge near the lever. Pull on the tab away from the glass to break the suction seal and remove from the windshield.

If this was helpful, please rate it 4 thumbs up. Thanks & good luck!
Read full answer
Sep 20, 2011 • Garmin GPS
0helpful
1answer

I do not know how to use the upholstery part to work
hi,

the owners manual is here at this link,

http://www.hoover.com/pdfs/manuals/F5807.pdf

I believe for you to work the upholstery tool the suction tank lid must come off, and the center channel there has to come out for the hose to go into, and then replace the suction tank lid again.

there should also be a second water hose to connect midway down the left side of the unit there little square push/pop out lever. the water hose will connect there and you should be good to go from there. Refer to the manual for the exact directions tho.
Read full answer
Nov 04, 2010 • Hoover SteamVac F5914-900 SpinScrub...
0helpful
2answers

I turn off the car, but key will not come out of ignition. Lock on shifter doesnt work. I can shift without pushing button on shifter. This is an automatic.
We had this problem on 06 and it is the shift button that doesn't pop out. You may be able to pull it out so you can remove the key for now. We had ours fixed under warranty (replaced)
Read full answer
Jun 16, 2010 • 2008 Chevrolet Hhr
3helpful
1answer

How do I replace the "Backup Lights" in my 2006 Nissan Murano?
You will need to remove the hatch trim panel, it has a hand hold that you have to pry out carefully, push in on the center buttons of the 4 plugs located at the bottom of the door trim, push in about 1/4" on the center little plug, then you can remove the complete plugs by prying under the edge. Once you pop the plugs out, push the plug you pushed in back out an additional 1/4' it will then be reusable to reattach the trim panel. The lights have to be removed, they snap in & you will need to pry on the side away from the switch end, they will pop out, remove the wiring noting the position for reassembly. Now that whole panel is removeable, it just snaps & pops off as it's held with a few clips & pawls. No screws or bolts.

If it's off, you'll be able to see the wiring to the back-up lights, twist counterclockwise & remove the bulb, reverse to reinstall.

It's not as tough as it sounds, I've had my cover off several times to work on the camera system.

good luck.
Read full answer
Feb 14, 2010 • 2006 Nissan Murano
2helpful
1answer

Unable to figure out how to inflate a bike tire
Could this help?

  1. Have the lever on the pump head pushed down, flat against the pump head.
  2. Push the pump head FIRMLY onto the tire valve.
  3. While still pushing firmly, flip the pump head lever up to lock the pump head onto the tire valve.
  4. Inflate to desired pressure.
  5. When finished, push the pump head lever back down and pull the pump head off the tire valve.
(Once you hook the pump up to your tire and start pumping, the back pressure will switch the flow to the bike valve output.)
Read full answer
Apr 07, 2009 • Cycling
1helpful
1answer

How to replace blub in headlight
The entire headlight comes out from the exterior of the car. When you open your hood, there is a lever that you need to slide up. The light will then pop out and you will be able to replace the bulb and then pop the light back in. You will have to push hard inorder to get the lever to go back down. We had better luck with two of us doing it... one pushing... the other working the lever.
Read full answer
Apr 06, 2009 • 2003 Volkswagen Beetle TDI
0helpful
1answer

Retro Westinghouse toaster works but toast will not pop out
YES .westinghouse used a clock timer to time all of there toasters in the 40s and 50s . remove the push down knob (there is a set screw under it) and the 4 screws under the toaster . the top will come off inside next to the push down lever there is a little clock timer . a drop of oil on the moveing parts of the timer will get it ticking again .....test your work by pushing down the lever stem (with it unpluged ) it should pop up when it times out . puting back on the top can be a pain but it does go back but at some point you may wonder ! with all toasters put down a towel before working on one to keep from scraching the mirror finish ......Please if this answer helped , please rate this 3 or 4 stars . and keep me in the paid answer department . A 1 or 2 may knock me down into the unpaid ranks. Thanks Cactus Bob
Read full answer
Feb 21, 2009 • Kitchen Appliances - Others
1helpful
2answers

The lock don't work properly
That lock mechanism has one additional adjustment hole. You have to disassemble the mixer. I recommend returning it if you can. If not, see my posts on "removing the motor cover" and that adjustment must be made on the inside. You will also be able to inspect the lock itself to see if the tooth is busted off. Good luck.
Read full answer
Jan 14, 2009 • KitchenAid KSM150PS Artisan Series Stand...
Not finding what you are looking for?

View Most Popular

Cascade Brix single hole lavatory faucet with 1-1/4" pop up waste 47360S-65

  • Plumbing

Related Question

I have a hitachi nv45...aand dropped it of the roof.It broke the pushing lever (part #888-883)I replaced it and now the gun isnt firing properly.The guns rapid fire doesnt work.You have to push the trigger...

  • Air Tools & Compressors

Open Questions:

0answers

My pedrollo 2CPm80 shows on but it is not working. I tried the reset button in the middle, it worked for 1 second, then it stopped. Any advice to help me make it working?
Read full answer
Be the first to answer Feb 26, 2020 • Plumbing
0answers

I have a pressure pump from dam to house, the problem is the pump is running but no water . If you turn power off to pump for a minute then turn back on it works again.
Read full answer
Be the first to answer Mar 24, 2019 • Plumbing
0answers

Hope someone can help me. I have the grundfos MQ3-45 pump and I wasn't getting enough water pressure. Went to check the pump which had the below lights and when I tried to reset it the pump never came back on. Could anyone help me locate what the possible fault may be ?
Read full answer
Be the first to answer Mar 13, 2019 • Grundfos Plumbing
0answers

I have the old 2 knob shower faucet. I replaced the gasket and spring but it has not stopped running. It is like it is half way turned on. Is there something else I need to replace?
Read full answer
Be the first to answer Nov 09, 2018 • Plumbing

See all NRS Cascade Brix single hole lavatory faucet with Questions

Related Topics

157 views

Ask a Question

Usually answered in minutes!

Popular Questions

How to adjust pressure switch onga pump.

NRS Plumbing

Sink drain slow

NRS A.H. Undermount Large and Medium...

ELECTRIC CONNECTIONS FOR AO SMITH ST1152

NRS 1.5 Hp 3450rpm 56J Frame 115/230...

Where can i get seaat for my ssww toilets they crack all the time

NRS Royal SSWW 1012 Dual-flush...

Motor hums but does not

NRS 1.5 Hp 3450rpm 56J Frame 115/230...

Top NRS Plumbing Experts

john h

Level 3 Expert

28867 Answers

Brad Brown

Level 3 Expert

19166 Answers

Tom Chichester

Level 3 Expert

62329 Answers

Are you a NRS Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...