Question about Xerox Phaser 4500 Printer

1 Answer

How do I reset a Xerox Phaser 4500 Centreware password to factory default.. or what is the factory default password? I have on which has been changed and nobody seems to know the PW anylonger

Posted by pete_henders on

Ad

1 Answer

Rick Kasper

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,072 Answers

This should restore it to default.


By default there is no username or password required to access CentreWare Internet Services. If a username and password have been configured for CentreWare Internet Services and you do not remember the username and / or password, reset the printer to factory defaults (NVRAM reset).
To reset the NVRAM, go to the front panel's Main Menu:

  1. Select Troubleshooting, then press the OK button.
  2. Select Service Tools, then press the OK button.
  3. Select Reset NVRAM, press the OK button.
  4. Select Reset NVRAM and Reset Printer NOW, then press the OK button to reset all the settings to their factory default values.


Posted on Mar 03, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How set factory default xerox 7800


Solution : Reset the Printer to the Factory Defaults (Reset NVRAM) WARNING: Only use the tool when directed to by Xerox Service. All user and system settings will be lost.
  1. Select [Printer] on the Touch Screen.

    7800-printer-menu-select.png


  2. Select the [Tools] tab.
  3. Select [Setup].

    6700_touch_screen_tools_setup.png
  4. Select [Service Tools].

    7800-ts-tools-setup-service-tools.png
  5. Select [Reset NVRAM]. A confirmation screen will be displayed.

    7800-ts-tools-setup-service-tools-reset-nvram.png
  6. Select [Reset NVRAM] again.

    7800-ts-tools-setup-service-tools-reset-nvram1.png
Related Knowledge Bases:

Mar 05, 2014 | Xerox Printer Division Xerox Phaser...

1 Answer

Reseting a printing module


No you have to replace it otherwise you get bad quality

Jun 19, 2013 | Xerox Phaser 4500 Printer

1 Answer

How to reset Xerox Phaser 3100 to factory settings?


First you have to enable the admin mode:
press and release: (down arrow) * #
on SOS1 change the 8th bit to 1 (counting right to left)
ie: 00100001 to 10100001 {press OK to confirm}
Now the admin menus are enabled.
To <Erase all. Reset to default configuration>
press (and release): (down arrow) #7

Feb 19, 2013 | Xerox Phaser 3100MFP

1 Answer

Xerox phaser 3600 factory reset


If you're locked out of the NVRAM reset from the control panel, you can still try performing a network reset by going to the Network menu and selecting Clear Setting. After rebooting, you should be able to get in through the administrative web interface at http:// using the default username of admin and password 1111

Aug 22, 2012 | Office Equipment & Supplies

1 Answer

How to reset admin password on phaser 3635


xerox machines come with default passwords.
once that password is changed only the changer knows it.
should he forget or lose the password he flat has a problem.
the reset requires a xerox laptop/tech to reset and they "will bill" you for doing it.

Jul 01, 2011 | Xerox Phaser 3635MFP/X Multifunction...

1 Answer

Xerox phaser 7760 saying "non-phaser imaging unit"


There is a snippet on the Xerox website to solve imaging unit recognition problems, link below. http://www.support.xerox.com/support/phaser-7760/downloads/engb.html?operatingSystem=winxp&fileLanguage=en_GB Usually this problem only occurs if the NVRAM has been reset or the engine board has been replaced without backing up the NVRAM. You can download the snippet to your printer through Centreware or by downloading the 'File Downloader' utility from the same page above.
Hope this helps.

Jan 09, 2011 | Xerox Phaser 7760DN Laser Printer

1 Answer

Password Problem Phaser 6120


Unfortunetly, you will have to reset the printer. Using the control panel go to the default setting and scroll to reset to factory settings. Then select yes and that should take care of it. If not, then in the rear of the printer under the cover, upper left side you will find the memory button battery. Remove the battery, unplug the unit, and turn it on for about a minute. Turn it off and put it back together and you should be ok. Good luck.

Feb 19, 2009 | Xerox Phaser 6120/YN Laser Printer

2 Answers

Centreware password on Xerox 7335


On mine it was the other way around username 11111 & Password x-admin

Jan 21, 2009 | Xerox DocuPrint 4517 Laser Printer

1 Answer

Xerox Phaser 8560 - Changing Menu from German to English Language


To select the default language on the Control Panel:
  1. Press the [Up] or [Down] arrow button on the Control Panel to select [Printer Setup] on the Display Screen, and then press the [OK] button.
  2. Press the [Up] or [Down] arrow button to select [Control Panel Setup], and then press the [OK] button.
  3. Press the [Up] or [Down] arrow button to select [Language], and then press the [OK] button.
  4. Press the [Up] or [Down] arrow button to select the required language, and then press the [OK] button.
  5. Press the [Back] button, located to the left of the 'Up' and 'Down' buttons, three times to return to the Main Menu.
To select the default language using CentreWare Internet Services (CWIS):
  1. Open an Internet web browser on the workstation.
  2. Enter the IP Address of the printer in the Address field, and then press [Enter] on the keyboard. The CentreWare Internet Services window will be displayed.
  3. Click on [Properties]. The Properties window will be displayed
  4. Click on the [General] folder on the left, and then select [Printer Defaults].
  5. Under the User Preferences section, select the language from the Set Control Panel Language pull-down.
  6. Click on the [Save Changes] button.
  7. Click on the [X] in the upper, right corner to close
If you are talking about the driver menu you have to delete and reload the driver with the english

Jul 22, 2008 | Xerox Phaser 8560MFP Laser Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

7,538 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

docukaaf

Level 1 Expert

38 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...