Why are the related videos to my videos not anything like my video? my tags say guns but related videos are christian rap videos.

Different ways



To COLD BLUE:



http://www.youtube.com/watch?v=Ef4fzXFvEZ8



HEAT BLUE:



tit=Gunsmithing+-+How+to+Flame+Blue+Small+Gun+Parts+for+a+Beautiful+Finish&c=2&sigr=11aeo7fu2&sigt=126f28ct5&ct=p&age=0&&tt=b">https://video.search.yahoo.com/video/play?p=how+to+heat+blue+gun+parts&vid=7badd3f699ff3b34ff9c9928c9d709be&l=1%3A03&turl=http%3A%2F%2Fts4.mm.bing.net%2Fth%3Fid%3DV.4909363603443979%26pid%3D15.1&rurl=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DlHuNwFdtzik&tit=Gunsmithing+-+How+to+Flame+Blue+Small+Gun+Parts+for+a+Beautiful+Finish&c=2&sigr=11aeo7fu2&sigt=126f28ct5&ct=p&age=0&&tt=b



CHEMICALLY:



http://www.brownells.com/gunsmith-tools-supplies/metal-prep-coloring/metal-bluing/index.htm

I THINK VID 3
I fixed mine works good easy too watch my video step by step i put it on youtube
http://www.youtube.com/watch?v=UFXSLOBL0Mg

It is not possible to use the Nikon SB-50DX directly on a Canon EOS Rebel camera. The Nikon flash gun hot shoe contacts do not match the Canon hot shoe contacts.
You can use the Nikon as a slave flash gun with a PC flash cord that matches the Nikon's flash contacts then connect the end of this flash cord to a flash trigger. The Canon's flash can then trigger the Nikon flash gun via the flash trigger.

Orings /other parts tend to stick when nailer is new. Dewalt uses some vinyl orings that have been causing premature failure. Be sure to add a few drops of oil when used. Too much oil is not good. Wrong oil will cause orings to swell and cause problems such as yours. Your nailer's firing valve can be reset by rapping the nailer against rubber surface such as a thick rugger mat or coiled rubber air hose. Remove airline and nails, being carefull not to damage the head, rap had against rubber mat and retest gun. If it did not reset rap against nose of gun and test. If no joy, you will most likely need to remove head and manually move cylinder up/down and /or check vinyl orings for failure. Before you try to reset the gun, make sure that the safety is pushing the firing pin all the way in. Air removed, look under the trigger as you push down on safey, if it does go all the way in try bump-firing the gun (for test have nails removed). Hold in trigger and quicky /firmly strike gun against rubber pad. Good luck

Pesronally I will try x-clamp . Well doing it make sure nothing has lifted on the mother board from heat expansion .."solder broke". YOUTUBE VID .. I seen a video on there as well where a guy raps half the motherboard in tinfoil nad then heated certain areas with heat gun .. It worked for him but I don't recommend it. The easiest way I could think to maybe fix this is unplug your fan overheat for 10 min or just until you see 2 red lights... then power off leave sit and cool down and reboot... Have fun choosing . WHat this would do is possible resolder itself if that is the issue .

where did you get the vids from. it sounds like the codec used for the vid is not ipod compatable. you may be able to convert them using free software like anyvideo converter or ipod robot. i tunes can play them because it has a greater library of video codecs (anything installed on the system... almost)

Sounds like your 'Box is on its way for an E74 Scaler Chip error mate.

Send Back to M$ if you can if you are out of warranty you could always apply a heat gun to the HANA chip to Reflow its Solder joints.