Question about Mk Diamond MK - 1503 - Flex Wet Stone Grinder

1 Answer

When i grind in the table top grinder the lock comes out lakshmi grinder

Posted by vijayalak865 on

Ad

1 Answer

Robert Koch

  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.
    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 165 Answers

Missing snap ring?

Posted on Feb 28, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Simonelli Microbar ii the grinder positions change settings every time make a coffee grinder mooving positions automaticaly
First, I'm not a Simonelli technician. Though I've worked on similar table top machines.
* The grinder on these small machines (compared to commercial units) are usually manually adjusted. They are usually built with a range from very fine Turkish coffee (like talcum powder) to a fairly fine auto drip grind. You should not be able to coarse it up as used in a french press.
* There should be some sort of indexing to indicate at least the direction to rotate the grind adjust, say; fine to coarse, or even Turkish to American, etc. Though it may be a generic + to -.
* There may be a positive 'click' to each setting or possible hold down lock mechanism. But the most common is a spring loaded nub that clicks into place. If yours did click before and not now then you need to take it in for service as you probably lost the part (tiny ball and spring)
* A thought; If your an "Americano" drinker (course grounds will hot water filtered through it to fill a Mug size cup) then it may have happened when adjusting to the larger grind size. The indexer ball and spring is only held down by the height of the grind ring. Exceeding the largest grind will allow the ball and spring to pop out of position which can fall into the burrs and destroy them. It may be possible the ball (steel ball bearing) is still trapped in the burr plates and moves them around. Can't grind steel.
* Still got problems? Check with vendor or MFR for service or replacement. Most machines of this type do not have serviceable parts or adjustments.
Aloha, ukeboy57

Jan 18, 2018 | Coffee Makers & Espresso Machines

1 Answer

Talea ring the grinder will not stop gringing
The Talea model is with a Ceramic grinder system. This can happen when the grinder outlet is clogged with coffee grounds. Fresh beans cannot enter the grinder as the outlet is clogged. Remember, the grinder in any machine is a grinder. It does not shovel the coffee grounds out and clean the outlet when it is clogged.
1- Check if the grind setting is too fine (powder like). If so change the setting to coarse. Fully automatic machines do not need fine grind. Keep the grind fineness like the table slat grain.
2- Check if the beans are dark roast and oily. Oily beans are a slow poison for any fully automatic machine. Change the beans to Non oily medium roast type.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Oct 16, 2014 | Saeco Talea Ring Plus Espresso Machine

2 Answers

Why does no brewed coffee comes out? bypass preground does work
- coffee-channel is stuck.

check google for calibrating/cleaning your gaggia.

Aug 27, 2014 | Gaggia Titanium Espresso Machine

1 Answer

Blade will not spin
While I don't have this brand or model of grinder, (coffee beans, spices?), I use a small elec. grinder for grinding coffee beans and unless the grinder and cover or perfectly lined up and locked in place, it willnot grind, a safety feature. Check and make sure everything is lined up so it closed with all the lines in place and the grinder is also put into the lock position.

Aug 21, 2011 | Cuisinart Grind Central DCG-20N Electric...

1 Answer

I clean with rice and it grinds coffee beans. Then I have to grind moRE RICE TO GET IT TO GRIND COFFEE AGAIN
Instead of rice, fill container about half full with regular table sugar. Grind that for 10-20 seconds. You should not only get coffee flavored powdered sugar but the sugar will soak up the flavors from your grinder.
Then simply clean as you normally would. Works great!

Mar 19, 2011 | Starbucks Barista Burr Grinder

1 Answer

I own a metabo 9-125 quick but can't don't know how to place the blade
On the silver part on top of the grinder is a button , press this button and hold it down. now turn the blade until it stops moving, this locks the blade, keep holding the button down and turn grinder over ,and turn the nut counter clockwise, and remove it , take old blade off ,put on new one .it should go over the shaft and at the bottom on a "fit" Make sure it is on the "fit". replace the nut and tighten. If you dont get the nut tight enough it will loosen while in use and the disc you are cutting/grinding with will wobble and may even come off causing possible injury .

Jan 29, 2011 | Metabo ® 12 Amp 9000 RPM Model WE14150...

1 Answer

Cleaned the Solis Maestro grinder and re set it to a fine espresso setting but the grind is coming out very course. What should i do?
Hi Your burr is not locked in. You need to remove the beans from the hopper. Remove the hopper. Remove the burr. Turn the grinder upside down over the trash can. Put the burr back in only make sure that the burr is down. Install the bean hopper and when you turn the bean hopper it should move the burr. Then you can adjust your grind. Make sure that the grinder is running is your going to a finer grind or you could break the grinder. You can turn it to a coarse grind any time.

Jan 12, 2010 | Solis Maestro G385 Electric Burr Grinder

1 Answer

I CAN'T LOCATE THE OWNERS MANAUL. NEED TO KNOW HOW TO LOCK THE DRIVE SHAFT ON A SEARS MOD. #21152 - 6'' BENCH GRINDER SO I CAN TIGHTEN THE NUTS THAT HOLD THE GRINDING WHEELS. TX MOE
Below I included a link to the manual for your grinder.
However it will tell you the same thing I'm going to tell you.
Most bench top grinders do not come with a shaft lock. In order to loosen or tighten the retaining nut you need to place a small wooden wedge between the wheel and the metal wheel shroud. This will prevent the shaft from turning. This may seem archaic but it serves a good purpose by preventing the over-tightening of the retaining nut.
Hope this helps.


http://www.managemyhome.com//mmh/lis_pdf/OWNM/L0410111.pdf

Oct 15, 2009 | Grinders

2 Answers

I don't know how to change the grinding blade on my makita angle grinder.
There is a nut that you release from the middle of the grinder wheel, (grinder blade)
This nut is flat and has four holes in it.

You will see you are providing a spanner wrench to remove this nut. The wrenches' actual name is Lock Nut Wrench. It has a U shaped end with two pins sticking out. On on each side of the U shape.

The pins are inserted into the holes in the flat lock nut, located in the middle of the grinding wheel. The wrench is laid flat against the grinding wheel, with the two pins of the wrench going into any two holes of the nut.

At the top of the Makita grinder you will see a Black button. The button is pushed down to keep the grinding wheel from spinning. Holds the grinding wheel in place, as you turn the lock nut loose. When you release the button, a spring inside pushes the button back up out of the way.

As you view the Makita grinder, Release Button towards the Back, grinding wheel towards you, the nut is turned to the LEFT, to loosen. It is a Left threaded nut.

The grinding wheel spins to the Right. Using a left threaded nut insures that the nut will stay tight, due to the direction the grinding wheel spins.

Oct 01, 2009 | Makita Usa Inc 9557PB 4 1/2" Angle Grinder

1 Answer

Rocky grind settings
The little button on the top locks the grind to the set position. If it is falling down and not engaging the collar, the collar will turn and rest the grind to a very fine setting. If this is happening, you have to clear the hole that it sits in. Easier said than done, but not too difficult.
First, remove the bean hopper. Then carefully unscrew the collar all the way out. You will see the grinding burrs here. This is where you can change them if needed - not our problem now. Lift out the button out, and there should be a spring too. The hole frequently gets packed with coffee grounds. You can use a drill bit - by hand - or a philips screwdriver (takes longer) to take the grounds out of the hole. Replace spring and button, working it up and down to ensure proper movement. Clean the threads of the collar with a brush and carefully screw back together. This step is important! You could ruin the grinder if the collar is not straight!
When you get it screwed in most of the way, start the grinder. Slowly screw it in until you hear a "zing" when the burrs touch. Stop and back off another 1/4 turn. This should be the espresso setting and the button should come up and lock the collar in place.

Good luck!

Dec 26, 2007 | Rancilio (RAROCKYND) Grinder

Not finding what you are looking for?

View Most Popular

MK - 1503 - Flex Wet Stone Grinder

  • Tools & Hardware - Others

Related Question

Simonelli Microbar ii the grinder positions change settings every time make a coffee grinder mooving positions automaticaly

  • Coffee Makers & Espresso Machines

Open Questions:

0 Answers

Staples stick out after stapling. Don't go all the way in. Any ideas.

Feb 23, 2021 | Staples Tools & Hardware - Others

0 Answers

I have a much older power fast heavy duty stapler 31600 it's shooting out two Staples at a time I cannot find the screws to take it apart so I can clean it. This is very frustrating it should be much simpler than this

Feb 11, 2021 | Staples Tools & Hardware - Others

0 Answers

A small metal piece fell out of my 50509 staples stapler while reloading. Where does it go

Feb 08, 2021 | Staples Tools & Hardware - Others

0 Answers

Dear everybody! I need a little help. I have a Paslode Im90i type nail gun. Last week on my nailer led going to flashing yellow, ok it need a service, i made it. After that i tried to reset the gun, but no way I don’t know, i follow the users guide step by step, But the gun doesn’t reset, in turn it working perfectly. So why i can’t restart the green light, Or have another way if i reset it. The steps which i did, i took it out the gas cartridge And the nails, turn on the gun flashing the yellow led turn it off, i pressing down the nailer, i pulling the trigger Turn on again the gun i waiting the fan is starting I let me go the trigger and 3 times i pull down and firing the gun within 5 sec. What i doing wrong?

Feb 08, 2021 | Tools & Hardware - Others

See all Mk Diamond MK - 1503 - Flex Wet Stone Grinder Questions

Related Topics

Mk Diamond MK - 1503 - Flex Wet Stone Grinder Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

6 Answers
Cant find staples for swingline 101 tacker

Tools & Hardware - Others

6 Answers
Why when I put my paslode battery on to charge

Tools & Hardware - Others

1 Answer
How to take apart a swingline Optima 45 stapler

Tools & Hardware - Others

2 Answers
My PaperPro One finger 15 sheet power Stapler just stopped stapling. ???

Tools & Hardware - Others

6 Answers
I bought a Powerfix Profi hand stapler from Aldi

Tools & Hardware - Others

Top Mk Diamond Tools & Hardware - Others Experts

Bill Boyd

Level 3 Expert

53816 Answers

ray gallant

Level 3 Expert

71004 Answers

ADMIN Canada
ADMIN Canada

Level 3 Expert

36647 Answers

Are you a Mk Diamond Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...