The second hand doesn't move . i tried pushing the buttons in the chronograph mode, the time mode and nothing. i have a citizen eco-drive BL5260.

put your finger nail under the crown and pull it out a bit ,then turn it to adjust the hands . when finished push it back in

Hi,

Hope this will helped you fixing the time of your Citezen divers watch. Just foolow the instruction below.

Change your Citizen watch's time zone without actually moving the clock hands. On the digital display, change the city that displays on the watch, which sets the time to the different time zone. The Citizen also has a calendar, timer, chronograph and LED lights. Since it is an Eco Drive watch, it is solar powered so you never have to replace the batteries unless its backup power source dies.
Difficulty: Easy Instructions

1. Pull the setting knob (crown) out one "tick" for setting mode.
   

2. Set the mode hand to "WT-S."
   

3. Pull the crown out one more "tick."
   

4. Press the top button on the right side of the watch for the city setting mode.
   

5. Press the lower button on the right side to "SET" the city.
   

6. Turn the crown to select a different city, which changes the time zone.
   

7. Push the crown all the way back in to finish setting the time.
   

Thank you for using Fixya.

OK try and follow these steps and it may help you set the time on your Watch. Once you understand the different function buttons on the edge of the case setting the time will be an easy task.

1-Note the 2 and 4 o'clock function buttons and the crown at 3 o'clock on the case edge of the Citizen Skyhawk Eco-Drive. These buttons set all functions of the watch.

2-Set the home city digital display function at 9 o'clock by pulling the crown to the first position. Rotate the crown until the mode hand in the subdial at 6 o'clock is aligned with TME. Press the 2 o'clock button until the nearest major city where you live appears. Press the 2 and 4 o'clock buttons at the same time to find the home city in the 3 o'clock digital display window. Once the city is selected, the time is automatically set by the automatic radio reception function.

3-Pull the crown out to the first position to manually set the time. Rotate the crown until the mode hand is aligned with the CAL, TME and RX-S position under the umbrella line. Push the crown flush with the case edge. Point the watch's 9 o'clock side in the direction of the radio transmitter. For example, if you live in Los Angeles, point the watch's 9 o'clock side east towards Ft. Collins, Colo., where the transmitter is located.

4-Hold down the 4 o'clock button for two seconds until the tone sounds and the second hand stops at the RX-S position. The second hand will then move to H, M or L found at the 2 o'clock subdial. Remain holding the watch in the same position. The second hand will move from the H, M or L position with the hour and minute hands to the correct time once the radio reception is completed.

5-Press the 2 o'clock button to start the chronograph's stopwatch. Press the button a second time to stop the timer. Press the 4 o'clock button to reset the timer.

6-Pull the crown all the way out and rotate it clockwise until the correct date is selected. Push the crown flush when finished.

IF you are still not able to set the time contact your dealer or the nearest Citizen showroom.

go to the citizen web site (citizen.com) and select "technical support" and then "setting instructions".

Enter the number off the back of your watch snd the click on "get setting instructions"

The instructions include the steps you need to take to zero the hands.

The chronograph will only run for 59 minutes 59.95 seconds.

If you do not have a set on instructions for your watch, you can find one on their web site (citizen.com)

When there, click on "technical support" and the on "setting instructions" and fill in the number off the back of your watch.

Just pull the crown out, turn it so that the bottom analog display is set on "CAL" and push crown back in. Voila!!

The manual explains it clearly From here http://www.citizenwatch.com/CUK/English/settingsresults.asp?caliber=e870

Put watch in direct sunlight, in a window for 8 hours. If battery indicator shows the watch is fully charged then you may need to look at what mode your watch is in.

good morning ! to set the Eco Drive Skyhawk citizen watch,full the crown carefully wind it slowly until you reach the correct time after that push the crown back to normal possition, if the hand is turning back to the wrong time just press the button on the up side until the turn to the correct time,thank you ! god bless !...

Got the same problem guys. i have one of the new electronic diving eco drives.
First time i managed to get it going again, by forcing all the hands to the top for diving mode, then back to normal, this action ´nudged´the minute hand back into motion, but a little later it stuck again at the same spot.
I guess mines going back to the factory, and i´m gonna b watchless for a few weeks :(