Question about Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

My oasis kenmore elite keeps flashing f 50 - Kenmore Elite Oasis 27052 Top Load Washer

Posted by valerynna200 on

Ad

1 Answer

Jahn27

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,554 Answers

The machine control through the rotor position sensor (RPS) cannot detect the motor running. The rotor is stuck, the rotor position sensor is faulty, or the machine control is malfunctioning. Open the lid and turn the drum manually. If it turns freely, activate the Manual Diagnostic Mode Test to check the functionality of the rotor position sensor and the machine control. If it doesn't turn freely, let us know to guide you in troubleshooting and repairing it.

The machine should be in standby mode when activating diagnostic test mode. That is, the machine is plugged in will all indicators off, or with only the Clothes Clean indicator on.

Choose any single button except Start, Stop, and Power. Press and hold the chosen button for 3 seconds and release it for 3 seconds; press it again for another 3 seconds and release it for another 3 seconds; press the same button again for another 3 seconds and release it (press, release, press, release, press; 3 seconds each).

The indicators will all light up for 5 seconds with 88 displayed in the Estimated Time Remaining display if the test mode has been successfully entered.

Repeat the procedure if the test mode is not activated. You may choose another button. Let us know if it cannot be activated after multiple attempts failed.

Press the same button chosen above before the indicators turn off (5 seconds). A single beep sounds and the two-digit console ID number is displayed. After 3 seconds the display is cleared (00) and the Add a Garment indicator flashes.

Open the lid and rotate the basket manually. The Wash, Rinse, and Spin status indicators should toggle on and off according to the rotation of the basket.

Press and release the 2nd Rinse button to lock the lid and the lid lock indicator turns on. Press and release the Rinse Speed button. The basket should spin slowly; pressing it again will raise the spin speed. The motor turns off and the basket stops the fourth time the Rinse Speed button is pressed.

With the basket stopped, press the Soil Level button to activate the Gentle wash action. Press it again to activate the Normal wash action. Press it again to activate the Heavy wash action. Press it again to turn off the motor and stop the basket.

Let us know the result of the test for us to guide you in troubleshooting the problem and eventually repair it.

Posted on Feb 22, 2010

Ad

4 Related Answers

Anonymous

  • 2 Answers

SOURCE: i have a kenmore oasis elite it beeps all the time and flashes F2

Code F2 means a stuck button. I removed the interface and lightly sprayed each with contact cleaner. So far this is working. The interface costs about $160 and contact cleaner, $10. Good luck.

Posted on Mar 18, 2009

Ad

fixrguy

  • 415 Answers

SOURCE: My Kenmore Elite Oasis HE is flashing a code

sound like the rps kit is required and is time comsuming will have to remove the back and console includes harness and new rps sensor and inset for sensor if not sure if you can perform it would be better to call service tech....must remove from the bottom of the motor location(main drive d/c motor)

Posted on Aug 19, 2009

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: Hello, I have a

The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 25, 2010

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: Kenmore Elite Oasis HE 27072. Keep getting UL

Check the Vibration damper rods to be sure that...
1. They are there and mount is solid.
2. If they are broken in 1/2.
3. The plastic knuckle mounts are not missing/broken.
4. There is oil in the shock absorber/spring section of the rods.

Also - there are suspension springs on the bottom of the tub that could be broken and/or missing.

Replace/repair as necessary.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Kenmore Elite Oasis washing machine has error code "UL" while in rising cycle and stop. Can you tell me what is the problem and how to solve it.


My Kenmore Elite Oasis washing machine will drain but not spin and it keeps jumping back and forth to different time cycles. It continually reads "UL" and I keep trying to adjust and balance the load but it does not help.

Jun 25, 2011 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Sears kenmore elite oasis dryer 110 67032600 check lint screen flashes doesn t heat


Hello,

Check the vent on the back. This is indicating a air flow issue. If the vent is clear ohm the heater out check it for continuity.


You can watch a video that explains how to complete this repair on your sears Kenmore Elite clothes dryer at the link below.

Sear Kenmore Dryer Video

Mar 11, 2011 | Kenmore Elite Oasis ST 6807 Dryer

1 Answer

I have a model 27096 top load kenmore elite oasis he washing machine that keeps flashing code F2 and keeps turning itself on. Help


"F02" is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a "SUDS" error may also be generated as a secondary error. This is an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:

1. Check the drain hose to make sure it is not kinked or clogged.
2. Check the electrical connections to the pump and ensure the pump is running.
3. Remove the drain pump filter and check for foreign objects and/or debris.

To check the drain pump, click on the following link for step-by-step instructions.


http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 20, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

4 Answers

F51 error


Hello, the F51 code is a motor rotor position sensor failure. It's best to call in the warranty service as there is a bunch of tests that need to be run to determine if it's the sensor or control board. If the tech wasn't any help, contact the store for a replacement.

Thanks

May 20, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

2 Answers

My Washer starts then beeps continuously and flashes F 50??? Can anyone tell me what this means?


F then 50 flashes when the motor rotor position sensor (RPS)
senses no rotation.
Does basket turn freely? If not, determine cause of friction.
If basket turns freely, see TEST #3, Page 10.


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Mar 25, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

2 Answers

In mid wash the Kenmore Elite Oasis HE flashes F51 and


check if basket turns freely. if it does replace the main board

Jan 28, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

2 Answers

Need to know what 50 means --washer keeps beeping after tub fills


Please see the following Whirlpool Service Manual for their Cabrio Washer (Basically the same as the Kenmore Oasis)

50 points to an obstruction keeping the basket drum from turning freely.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/409753510a90c8be852571e90073421b/$FILE/8178583.pdf



Nov 08, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Elite Oasis HE


The f50 codes mean you have a bad ccu control board (The board behind the control panel) . This was a faulty board from the factory. They have remanufactured the part. So change that and you should be good to go.

Nov 18, 2008 | Kenmore Elite 45986 Front Load Washer

2 Answers

Kenmore Elite Oasis HE/ Error Code F1


repl/ main control board reason for error code F 1 ,,,nothing else

Nov 08, 2008 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
Kenmore Elite Oasis 27052 Top Load Washer Logo

486 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Tracy

Level 3 Expert

575 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...