Handset says unregistered

Welcome to FixYa.

Reset the units/set up by doing the following:

• Turn OFF all the HANDSETS.
• Remove the batteries of the HANDSETS.
• Unplug the power source of the BASE.
• Unplug the phone line of the BASE.
• Let it stay that way for 30 mins.
• Insert the battery again of the HANDSETS, make sure it is charged properly.
• Plug back the power source of the BASE.
• Plug back the phone line to the BASE.
• Register any handset that is unregistered (refer to manual).

Keep me posted.

Jas247

1. Place the unregistered handset on the charger.
2. Press and hold the FIND button for 4 seconds on the base.
3. Release the FIND button once the IN USE light starts to flash.
4. A confirmation tone will sound when registration is successful. Handset X is displayed where X denotes the number of handsets. The phone will then go back to idle.

just in case you need it:

User Manual Clarity D613C Combo Pack (D613 with D613HS)

Don't forget to rate if this was helpful :-)

Find the company that makes it and go online. The company is usually happy to let you download the instruction manual or they will send it to you as well.

UNREGISTERED means the phone has not yet been set up to work with any particular base. I don't have any Phillips phones, so I can't tell you the procedure, but it should be outlined in the owners manual. Look for registering your handsets.

Hi,
We got one from
www.espspecialbatteries.co.uk

[ARC20x User Guide p20: 11 Handset Registration]
To register a new handset:

1. Press and hold the HANDSET LOCATOR on the base unit until you hear Registration tone (repeated 'beeps')
2. On the handset, press the PROG then the UP or DOWN button to display "REGISTER"
3. Press the PHONE/OK
   -> The display shows "BS 1234". If any of these numbers is steady (not flashing), then the handset is already registered to that base unit.
   
4. Press 1 to select base unit number 1
   -> The display shows "BASE PIN _ _ _ _"
5. Key in the system PIN (default 0000) and press the PHONE/OK
   -> The display shows "WAIT _ _ _ _" for a few moments, while the handset searches for a base. Then it shows a list of handset numbers which are still free on the base unit.
   (For example, "1 34 6" indicates that numbers 1, 3, 4 and 6 are free; 2 and 5 are already assigned to other handsets.)
6. Key in a free handset number
   -> After a moment, the display should show the handset's name and number.

If registration fails...

• Try again, making sure you begin step 2 as soon ans Registration tone starts.
  

Maybe a little bit late, this is the solution for registering the handsets: hold the button on the base until it starts beeping, then, on the handset, go to the Register menu, select base number - in my case it's 2, then it will ask the PIN - the default is 0000, and that's it.

IF YOUR HANDSET WAS WORKING AND THEN STOPPED WITH "UNREGISTERED":
If lowercase unregistered is in main display and a reg. appears under the left soft key:
Press the left soft key below REG. and then press and HOLD the button on the top of the base station until the two indicator lights on top of the base station turn off. Wait until handset signals with beeps and registered. You are done

THIS IS FOR FRESH OUT OF THE BOX REGISTRATION OF UNREGISTERED HANDSET
Press REG Register shall be highlighted.
Scroll to Register. Press Select.
Enter the system PIN (Default: 0000). Use
CLEAR to correct typing errors.
Press ENTER to confirm.
• Your handset starts searching for the base.
Press and HOLD the round button on top of the base unit until the two
indications turn off.
• If registration is successful, the signal icon

I solved it out u must pres de paging button on the base while registering the phone to base keep the paging button pressed until starts to beep like 5-10 sec. Good Luck

If you bought the base and handset together they should already be registered. If not then the instruction manual is downloadable here: MANUAL


The relevant section is on page 16 - here is a copy:

4 handsets can be registered to the base station. A handset
can only be associated with 1 base station.
�� To register another handset
First enter registration mode by unplugging and
plugging back in the power adapter to the
electricity supply.
Handsets registering / unregistering ( )
�� To unregister the handset you use
enter the RC code*
�� To unregister all the handsets (except the handset you are using)
enter the RC code*
Once the menu is selected, enter the RC* code written under the base and press
to confirm.
Warning : If you wish to associate a non-Philips handset to the DECT 211 or DECT 215 base
stations, make sure that these handsets are GAP compliant otherwise they will not operate properly.
*RC code
(Registration
Code) is
written under
the base.
Warning : Once unregistered, the handset is no longer operational.

Please rate my assistance this should be a fixya!