I have a bc144xl and I don't know how to cancel a frequency so I can put new frequency in. Please Help!!!! Thanks. Chris

Good Luck:

Try to turn off unit and remove battery pack, then reinstall it after 10 mins and while its off press scan button for 5 seconds and turn it back on. it should automatically go to scan mode on WX

The best programming instructions for your scanner are in the manual that you can download and print, at no cost, here:

http://www.box.net/shared/it6eozctkb

For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:

www.RadioReference.com

Bill B.
Listening in since the 60's

Usually with a noise-canceling headset, it might block out most noises, and varying to the quality it might or might not work with people's voices. Normally, there is a small switch on the headset themselves to start emitting a kind of "white noise" to cancel out the outside noises. The headset might cancel out noises that YOU hear from the outside, but it doesn't guarantee that through the mic.

I don't think there is software needed to be installed. I would look a bit more to the instruction manual to see the precise specs on the headset.

Please Rate. Thanks :-)

Programming the BC248CLT is fairly simple, and detailed instructions can be found in the factory manual that you can download and print here:

http://www.uniden.com/pdf/BC248CLTom.pdf

What you can program and what you can hear will depend on your location. Many communities now use trunking systems and digital (APCO-25) systems, and your scanner is not compatible with either. For a comprehensive database of active frequencies and systems in your area, visit:

www.RadioReference.com

Bill B

To program a frequency into your scanner:

- Power scanner ON.
- Press MANUAL to stop scanning.
- Enter the number of the channel that you wish to program. For example, enter 1 then 0 for channel 10.
- Press MANUAL.
- Enter the frequency, including the decimal point. For example, 408.165

Need the manual for your scanner? You can download/print it here:

http://www.scribd.com/doc/2056189/UBC144XLT

For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com

Bill B

I can't find the manual for that model, but here's how to program it:

- Power the unit ON
- Press MANUAL to stop scanning
- Enter the channel number that you wish to program (01-16)
- Press MANUAL
- Enter the frequency to be programmed, including the decimal (example 156.25)
- Press E (Enter) to confirm
- Press MANUAL to advance to the next channel

For a comprehensive database of active frequencies in your area visit

www.RadioReferencve.com

Ok answers to both of you questions. First, in order to get you booklet go to:

http://www.scribd.com/doc/2056189/UBC144XLT

I found your booklet right there in black and white. The programming instructions are on page 11 of the viewer and page 9 in the manual itself.

Here is how to program a channel.
1. hit manual to stop the unit from scanning.
2. Input the Channel # you want to program.
3. Press manual again to go directly to that channel.
4. press the frequency you want on that channel, remember the decimal point.
5. Press "E" to save or "Enter" the frequency.
6. Lastly assure that this channel is not "Locked Out" by seeing that the L/O is not illuminated on the display when you are on this channel.

Hope this helps,

[email protected]

Hello cw1966,

The frequencies for this unit are:

Channel / Frequency
1 462.5625
2 462.5875
3 462.6125
4 462.6375
5 462.6625
6 462.6875
7 462.7125
8 467.5625
9 467.5875
10 467.6125
11 467.6375
12 467.6625
13 467.6875
14 467.7125
Output power is < 500 mW ERP.

Hope this helps!
Ken
"Go Ahead. Use Us."

What make of scanner ??? if its a uniden bearcat try there web site they have user manuals there for download
www.uniden.com