The wireless remote transmitter no longer works.

Acura Remote Alarm / Central locking

Model: CL Year: 2001-2003
Model: TL Year: 1998-2006
Model: MDX Year: 2001-2006
Model: RDX Year: 2007-2009
Model: RL Year: 1996-2004
Model: RSX Year: 2002-2007
Model: TSX Year:2004-2008

System Operation

• Pressing remote transmitter LOCK button once activates alarm and central locking.
• Pressing remote transmitter UNLOCK button once deactivates alarm (if fitted) and unlocks driver's door only.
• Pressing remote transmitter UNLOCK button once also activates driving position memory. Driver's seat and mirrors move into memory position specified on remote transmitter when driver's door opened.
• Pressing remote transmitter UNLOCK button twice within 5 seconds unlocks all doors.
• Pressing remote transmitter trunk release button for 2 seconds activates trunk release.
• Pressing remote transmitter PANIC button for more than 1 second activates panic alarm.
• Pressing any of the remote transmitter buttons deactivates panic alarm.
• If vehicle unlocked and doors not opened within 30 seconds, locks are reactivated.

Synchronization.

when

• Remote transmitter battery replaced.

How

• Press remote transmitter LOCK button or UNLOCK button 5-6 times.
• System should now lock and unlock vehicle to indicate synchronization procedure complete.
• Check operation of remote transmitter

Programming

How

• Obtain all remote transmitters.
• Switch ignition ON.

Proceed as follows:
NOTE:Point remote transmitter at central locking signal control module (located behind glove box).

• Within 4 seconds: Press LOCK button or UNLOCK button of first remote transmitter.
• Within 4 seconds: Switch ignition OFF.
• Within 4 seconds: Switch ignition ON.

Repeat procedure above twice.

• Within 4 seconds: Press LOCK button or UNLOCK button of first remote transmitter.
• System should now lock and unlock vehicle to indicate programming mode activated.

Within 10 seconds:

• Press LOCK button or UNLOCK button of first remote transmitter, allowing doors to lock and unlock once.
• Press LOCK button or UNLOCK button of each remaining remote transmitter to be programmed, allowing doors to lock and unlock once as each remote transmitter is programmed.
• Switch ignition OFF.
• Remove key
• Check operation of all programmed remote transmitters.

Immobilizer

System Operation

• System arms 5 seconds after switching ignition OFF. Immobilizer warning lamp flashes during this time
• Switch ignition ON.
• Immobilizer warning lamp illuminates for 2-3 seconds.
• If immobilizer warning lamp illuminates for 2-3 seconds then flashes rapidly:
• Key code not recognized.
• Remove key and try again.

Programming

When

• System malfunction.
• Key added or replaced.

How
Immobilizer can only be programmed using diagnostic equipment.

Model: MDX Year: 2007-2009
Model: TL Year: 2007-2008


System Operation

• Pressing key LOCK button once locks the vehicle.
• Pressing key LOCK button twice within 5 seconds activates the alarm.
• Pressing key UNLOCK button once unlocks the driver's door only and deactivates alarm.
• Pressing key UNLOCK button within 5 seconds unlocks all doors and tailgate.
• Pressing key UNLOCK button within 5 seconds and holding will open windows and sunroof

NOTE: Models with "Technology Package": Alarm central locking functions can be altered using digital multifunction display in instrument panel.

• Pressing key PANIC button for more than 2 second activates panic alarm.
• Pressing any of the key buttons or turning ignition ON deactivates panic alarm.
• System will automatically lock all doors when vehicle is driven above 15 mph (if function selected).
• If vehicle is unlocked and doors or tailgate not opened within 30, 60, or 90 seconds (depending on programming), locks and alarm system are automatically reactivated.
• Pressing tailgate release button once will open, close or reverse direction of tailgate.

Programming

When

• Key remote transmitter added or replaced.
• System malfunction.

How

• Obtain all keys fitted with remote transmitters.
• Ensure doors, trunk / tailgate and hood are closed and unlocked.

NOTE: A maximum of 5 remote transmitters can be programmed.

• Switch ignition ON.

Proceed as follows:

• Within 4 seconds: Press LOCK button or UNLOCK button of first remote transmitter.
• Within 4 seconds: Switch ignition OFF.
• Within 4 seconds: Switch ignition ON.
• Within 4 seconds: Switch ignition OFF.

Repeat procedure above twice. Locks should cycle when button in pushed.

• Within 4 seconds of each other press LOCK button or UNLOCK button of each remaining remote transmitter to be programmed, allowing doors to lock and unlock once as each remote transmitter is programmed.
• Switch ignition OFF.
• Remove key.
• Wait 10 seconds.
• Check operation of all programmed remote transmitters.

Immobilizer

System Operation

• System arms when vehicle is locked using the remote transmitter.
• If key code is not recognized:
• Engine starts, then shuts off.
• Immobilizer warning lamp flashes once, then blinks until ignition is switched OFF.
• With ignition switched OFF, immobilizer warning lamp will flash 10 times to indicate the system has reset.
• Remove key and try again.

Programming

When

• System malfunction.
• Key added or replaced.

How

Immobilizer can only be programmed using diagnostic equipment

Model: RL Year: 2005-2009



Programming

When

• Remote Transmitter added or Replaced.
• System Malfunction.

How
Remote Transmitters can only be programmed using diagnostic equipment.


Automotive and Commercial Locksmith Acura Remote Transmitter Programming...

A Chrysler Transponder Key once programmed into a one car cannot be programmed to work any other car.

The transponder code identification is learned by the Sentry Key Immobilizer Module during programming. The Sentry Key Immobilizer Module sends the "Secret Code" to the transponder key and is retained by the transponder key during programming. After programming of the transponder key identification to the Sentry Key Immobilizer Module and the Secret Code is exchanged, the Sentry Key Immobilizer Module will ask for the transponder identification and the Secret Code every time the key is turned to ON or START.



No Emergency "Start" procedures for Chrysler vehicles.



Chrysler Key Operation and Programming



Model: 300 Year: 2005 - 2008

Model: 300C Year: 2005 - 2007



Remote alarm / central locking



System Operation

• Pressing key LOCK button activates alarm and central locking.



• Pressing key UNLOCK button once deactivates alarm system and unlocks driver's door.



• Pressing key UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors and trunk.



• Pressing trunk lid button twice opens trunk lid.



• System will automatically lock all doors when vehicle is driven above 15 mph.



• Additional functions can be set to respond to the transmitter.

Programming



When

• Key transmitter added or replaced.

How

• Key transmitter is programmed during immobilizer programming procedure.

Immobilizer

System Operation

• Switch ignition ON.



• Immobilizer warning lamp illuminates for approximately 3 seconds.

Programming



When

• Keys added or replaced.

How:



NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using diagnostic equipment.

• Insert first programmed key into ignition switch.



• Switch ignition ON for at least 3 seconds but no longer than 15 seconds.



• Turn ignition OFF and remove key.



• Withing 15 seconds insert second programmed key into ignition switch and turn ignition ON.



• After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash.



• Turn ignition OFF and remove second programmed key.



• Within 60 seconds insert non programmed key into ignition switch and turn ignition ON.



• After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds.



• Switch ignition OFF.



• Remove Key.

Check operation of programmed key transmitter.

Repeat procedure for additional key transmitters if required.





Model: 300M Year: 1999 - 2003

Model: Concorde Year: 1998 - 2003

Model: LHS Year: 1998 - 2001

Model: PT Cruiser Year: 2000 - 2005





Remote alarm / central locking



System Operation

• System will automatically lock all doors when vehicle is driven above 15 mph.



• Pressing remote transmitter UNLOCK button once deactivates alarm system and unlocks driver's door only.



• Pressing remote transmitter UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors.



• Alarm / Central locking functions can be altered using remote transmitter.

Programming

When

• Remote transmitter added or replaced.

How:

NOTE: One programmed Remote transmitters must be available for the following procedure to operate.

• Obtain all remote transmitters.

NOTE: Any existing remote transmitters not used during programming will become inoperative.

• Switch ignition ON.

Using a programmed remote transmitter proceed as follows.

• Press and hold remote transmitter UNLOCK button.



• After holding the UNLOCK button for at least 4 seconds but no longer than 10 seconds, press remote transmitterPANIC button for at least 1 second and release both buttons.



• Ensure acoustic signal is emitted indicating programming mode active.



• Within 30 seconds carry out the following procedure for each remote transmitter (including previously programmed remote remote transmitter)



• Press any button of each remote transmitter to be programmed.



• Ensure acoustic signal is emitted after each remote transmitter operation.



• Programming must be completed within 30 seconds.



• Switch ignition OFF or wait 32 seconds to exit programming mode.

Ensure final acoustic signal is emitted.

Replacement remote transmitters can also be programmed using diagnostic equipment.



Immobilizer



System Operation

• System arms after switching ignition OFF.



• Switch ignition ON.



• Immobilizer warning lamp illuminates for approximately 3 seconds.

Programming



When

• Keys added or replaced.

How

NOTE:Two programmed key transmitters must be available for the following procedure to operate.

• Obtain all keys.



• Using first programmed key turn ignition switch ON and wait 3 seconds, return to OFF position and remove key.

NOTE: First and second programmed key operations MUST be performed within 15 seconds.

• Insert second programmed key and switch ignition ON.



• Wait approximately 10 seconds.



• Ensure immobilizer warning lamp begins to flash and an acoustic signal is emitted.



• Switch ignition OFF and remove key.



• Within 50 seconds, insert new key and switch ignition ON.



• Wait approximately 10 seconds.



• Ensure acoustic signal is emitted and immobilizer warning lamp remains illuminated for 3 secondsindicating programming completed.

For each additional key repeat procedure starting from the beginning.

Replacement keys can also be programmed using diagnostic equipment.



Automotive and Commercial Locksmith Chrysler Remote Control Programming...

USE ONLY WITH SERIES II ELECTRONICS.<br /> Older Transmitters and Receivers will not work with these new electronics. There are no Security Code Switches inside the Door Operators, Transmitters and Receivers.<br /> <br /> <br /> To Program Receiver <br /> Step 2-1 Locate the Learn Code Button and Radio Signal Indicator on the Power Head Receiver of your Door Operator.<br /> <br /> Step 2-2 Press a Transmitter Button once within 30 seconds.<br /> <br /> Step 2-3 Press and release the Learn Code Button<br /> &bull; The Radio Signal Indicator will blink approximately 2 times per second.<br /> &bull; The Radio Signal Indicator stays lit - SOLID.<br /> <br /> Step 2-4 Press the same Transmitter Button within 30 seconds.<br /> &bull; Radio Signal Indicator will go out.<br /> <br /> NOTE: If a second Transmitter Code is not confirmed within 30 seconds or if a different Transmitter Code is sent, the Radio Signal Indicator will blink approximately 4 times per second, then programming will stop. If programming stops, repeat Steps 2-2 through 2-4.<br /> <br /> Step 2-5 Repeat Steps 2-2 through Step 2-4 for each Transmitter, Wireless Keypad or other access device to be learned.<br /> <br /> NOTE: A maximum of 7 Transmitter, Wireless Keypad and other access device Codes can be stored into Receiver Memory at one time. If a Transmitter becomes lost or if you want to delete a Transmitter, Wireless Keypad or other access device, proceed to ERASING ALL RECEIVER MEMORY.<br /> <br /> <span style="font-weight: bold;">Multi-Button Transmitters</span><br /> <br /> NOTE: Only ONE button of a Multi-Button Transmitter can be programmed into a single Receiver. The other buttons are to control other Door Operators.<br /> <br /> NOTE: If you are replacing a lost or stolen Transmitter:(1) Erase ALL Transmitter Codes from the Receiver memory. (2) Reprogram the Receiver with the remaining Transmitters Codes.<br /> <br /> <span style="font-weight: bold;">Erasing All Receiver Memory</span><br /> <br /> Step 4-1 Press and HOLD the Learn Code Button for 10 seconds or until Radio Signal Indicator goes out.<br /> <br /> <span style="font-weight: bold;">ALL Transmitter Codes are erased from Receiver memory.</span><br style="font-weight: bold;" /> <br /> Step 4-2 Reprogram the Receiver with the remaining Transmitter Codes (Repeat Steps 2-2 through 2-4).<br /> <br /> <span style="font-weight: bold;">Step 5-1 Battery replacement</span><br /> &bull; Slide Battery Cover off of Transmitter back.<br /> &bull; Replace with new batteries.<br /> &bull; Slide Battery Cover back on.<br /> <span style="font-weight: bold;"><br /> Step 5-2 Visor Clip installation</span><br /> &bull; Slide Visor Clip into back of transmitter until it snaps into<br /> place.