My LCD is completely black, just doesn't turn on. I'm still able to operate the menu by guessing their position on the screen but can't really do much as I'm noty able to see anything on the screen or on the viewfinder. When the LCD is fixed with the camera facing outward, I'm able to see the menu finctions on the viewfinder, the "touch" sense of the LCD is fine, I just am not able to see anything on the screen itself.My LCD is completely black, just doesn't turn on. I'm still able to operate the menu by guessing their position on the screen but can't really do much as I'm noty able to see anything on the screen or on the viewfinder. When the LCD is fixed with the camera facing outward, I'm able to see the menu finctions on the viewfinder, the "touch" sense of the LCD is fine, I just am not able to see anything on the screen itself.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You have 2/4/6 timing marks 180 degress out on exhaust or intake cam .
Did your special tool ?
Rotate the crankshaft using the J 42098 until the #1 cylinder is at 60 degrees before top dead center (BTDC).
Install theJ 42069 Crankshaft Locking Tool.
Rotate the crankshaft in the engine rotational direction (clockwise) using the J 42098 until the #1 cylinder is at top dead center (TDC) and tighten the lever arm to the water pump pulley flange.
Important: Ensure that the alignment of the crankshaft is not 180 degrees off. The alignment mark must align with the corresponding notches on the rear timing belt cover.
Install the 1-2 and 3-4 camshaft locks, the J42069-1 Timing Belt Alignment Kit and the J42069-2.
Important: Do not rotate the crankshaft if the camshafts are not locked in place with the 1-2 and 3-4 camshaft locks (J42069-1 and J42069-2).
Important: Do not rotate the camshafts unless the crankshaft is at 60 degrees BTDC or the valves may contact the crankshaft.
Loosen the tensioner pulley.
Remove the timing belt.
Unfortunately, most likely. Sounds like either the screen, or the actual sensor is dead. If when playing back the recordings on to your TV or computer you discover that they're still blank, then your camera is dead.
make sure you open the lens 90 degrees to the camcorder.normal operation of the cam will allow you to rotate the lcd to a maximum of 180 degrees and can eve close it with the lcd screen side facing out. you can try pressing the reset button.if it still won't work try removing the battery and unplugging it from the ac adaptor for at least a minute.if still doesn't work properly,issue could be with a bad ribbon inside the lcd that loses contact when you turn it clockwise.that of course would need replacement or repair.
Inside the door hinge area is a small switch that normally would turn off the viewfinder and turn on the LCD panel. THat switch could be defective or mechanically not being switched. WIthout opening up the unit, I can not tell specifically. This shouldbe a simple repair for any shop that repairs cameras.
My LCD is completely black, just doesn't turn on. I'm still able to operate the menu by guessing their position on the screen but can't really do much as I'm noty able to see anything on the screen or on the viewfinder. When the LCD is fixed with the camera facing outward, I'm able to see the menu finctions on the viewfinder, the "touch" sense of the LCD is fine, I just am not able to see anything on the screen itself.
×