Question about Yamaha RX-V661 Receiver

1 Answer

No display info on receiver

Just bought a yamha receiver RX-V661 7.1 and after conncecting all of the speakers I noticed two problems. 1. No display; I could get the radio, Dvd and Satellite TV to work with a little sound but no display light. 2. Back surround speakers no sound. I checked and rechecked all connection. I attempted the Auto Setup with the optimizer, but again no display lights and it stated Video monitor will display blah blah, What video monitor. Help

Posted by El_Coach on

  • El_Coach Feb 25, 2008

    Thanks for the info. I did plug my video monitor(TV) to the rear of the Yamaha, using the HDMI ports. I then attempted to use an alternative connection by using the YBR and S video and nothing. No LCD display. Thanks for the advice. I will take the receiver back.

×

Ad

1 Answer

Scott Frye

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,175 Answers

Try plugging a video monitor AKA your TV into that monitor output connector on the rear of the yamaha.
Select video in on the TV and see if anything shows up from the yamaha

Sounds though like the receiver has serious issues. If you can get your moeny back , do so

Posted on Feb 24, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuck on rx mode


Rx is an abbreviation for receive. (Tx is transmit) There are a variety of reasons a radio will be "stuck" in Rx:
1) Another radio in the group is stuck in transmit and you cannot reply if your radio is receiving the other radios transmission.
2) Your radio is programmed for Rx only.
3) Your radio has a Tx problem such as a bad mic, or something covering the mic opening.
4) Your battery is low or bad. It takes more energy to Tx than to Rx.

Best regards.

Feb 07, 2014 | Cobra LI3900-2DXVP (14 Channels) 2-Way...

1 Answer

Message volume fixed


Zone 2 Setup on the RX-V773 using the ZONE2/PRESENCE Extra Speakers The RX-V773 extra speaker terminals can power one set of speakers for Zone 2 or Presence speakers. If the extra speaker terminals are utilized then the RX-V773 cannot be set for Bi Amp (Surround Back/BI-AMP terminals). Setting the Extra Speaker Terminals Note: The RX-V773 remote control will be used to access the On Screen Menu of receiver. 1. Press the On Screen button on the remote control to enter the On Screen Menu. 2. The On Screen display should be displayed on the TV/Monitor. 3. Press the Arrow Down button on the remote until Setup comes up in the screen. 4. Press the Enter Button on the remote control. 5. The Setup Menu will come up across the TV/Monitor screen. 6. Use the Arrow Left & Right buttons on the remote to navigate to Speaker. 7. Press the Arrow Down button on the remote to select Manual Setup. 8. Press the Enter Button on the remote control to enter Speaker Manual Setup menu. 9. Speaker Manual Setup menu with Power Amp Assign highlighted will come up. 10. Press the Enter Button on the remote control to enter Power Amp Assign menu. 11. Speaker Manual Setup, Power Amp Assign menu will come up with Basic highlighted. 12. Press the Arrow Down button on the remote to select 7ch+1ZONE. 13. Press the Enter button on the remote to select 7ch+1ZONE. 14. Press the On Screen button to exit the on screen menu. To control Zone 2 using the RX-V773 remote, the switch at the upper left side (above the BD/DVD Scene button) of the remote must be set to Zone 2. To see the operations on the front of the Yamaha receiver you must press the Zone Control button on the front of the receiver. Note: Only analog signals can be sent to Zone 2. If you want to output the sound from Zone 2, connect an external component to USB Thumb drive, USB iPhone/iPod, Network, AV 5-6 or Audio 1-2 by analog connection. For AM/FM radio the antennas must be attached.

Aug 19, 2012 | Yamaha RX-V773

2 Answers

I have two uniden GMR1088-2CK radios, If I press the transmit button on the side and speak into the Mike you can see tx appear in the display, the 2nd unit receives the call, rx appears in the display and...


Hello,

What this code indicate mean that your radio have have been compress with power however the can also be an indication of lower power supply but most of the time is always power compress.

What you need to do to solve this code problem is to put off the radio for some time allow it relax, then remove the battery if possible after some time replace it if you are able to remove the battery then put on the radio and operate it.

Good luck.

Jan 15, 2011 | Radio Communications

1 Answer

The Yamaha Reciever RX-V465 is connected to my digital TV by fibre optic cabel. I have sound when I connect my MP3 to the V-Aux and the speakers are displayed on the display window of the Reciever same as...


Please check your TV settings and the optical cable.
The speaker icons disapper from LCD display when the receiver does not detect any input signal throught the optical/coax/hdmi cable.

Dec 13, 2010 | Yamaha Rx-v465/rxv465 Home Theater...

1 Answer

Yamaha rx-365 reciever not showing all speakers


I,m not familiar with the Yamaha but most receivers are set up the same way. In your setup menu are the speakers marked on in the display?. Your DVR needs to be transmitting in 5.1 to start with. If this is the case then make sure you select the correct audio function on the receiver.

Mar 04, 2010 | Yamaha Rx-v365 A/V Home Theater Receiver

2 Answers

Yamaha RX V 657 - No Sound Output, and No input detection


Bad DSP chip. The only other possibility is if you have the "Direct" on. On the front of the receiver it's a small button. Also make sure your "Speaker Select" A/B is "on" You will see it on the display, it's also a small button on the front of the receiver. If all this is correct and you still have no audio, it's a bad DSP chip. Not worth repair, it's 400-500 repair. Not very common in a Yamaha RX-V series, but I have seen it. I'm a Yamaha Dealer. If you need further help, post a comment and I will be glad to help you further.

Aug 23, 2009 | Yamaha RX-V663 Receiver

1 Answer

RX-V1600 when i turn on no sound or channels display on


If you are sure that the speaker wiring is correct and connections are good, then:
  • Check the input and output connections are correct for each source.
  • Check that the input mode is not set to DTS or Analog - rotate the input selector to the source and the press the input mode, set it to Auto.
  • Also check that the front speakers to be used are selected A or B (or A+B).
  • If there is an optimiser microphone supplied with this receiver, ensure that it is not still plugged in.
Hope one of these solutions work for you.

Jul 19, 2009 | Yamaha RX-V1800

1 Answer

Little or no sound JVC RX6010V


i had the same problem but i went to adjust settings and it says right speaker left speaker and you have to set them on ten

Jan 02, 2008 | JVC RX-6010V Receiver

8 Answers

JVC RX-884VBK RECEIVER


The JVC RX-884VBK is a great machine, I had it for over 5 years and had no problem at all. I came across the (NO SOUND at all) and I believe it is an easy fix. Check the Front left, there are 2 keys marked 1 and 2 for SPEAKERS output, sometimes you don't notice that you connected the speakers to 1 and the 2 key is pressed. You could have both keys pressed and you will get the sound. I hope that helps.

Nov 29, 2007 | JVC RX-884V Receiver

Not finding what you are looking for?
Yamaha RX-V661 Receiver Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers

Will

Level 1 Expert

2 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...