Dishwashers Logo

Related Topics:

Kevin Hogan Posted on Nov 06, 2017
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Bosch SGS5332GB dishwasher. drain pump runs all the time

Bosch SGS5332GB dishwasher. When program starts the drain pump runs and pumps out OK. (If I pour some water in it empties ok) Then no water enters and the drain pump runs continuously. Once or twice it has continued with the program but near the end of program the drain pump runs continuosly so prgram sticks at this point. Any Ideas?

1 Answer

James Gettemy

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Expert 232 Answers
  • Posted on Nov 06, 2017
James Gettemy
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: Mar 12, 2012
Answers
232
Questions
0
Helped
133793
Points
821

There is a float under the machine that tells the pump to shut off. If the float is stuck or bad, the machine will keep draining. I am including a web site that might help. Bosch Dishwasher That Will Not Stop Draining Hunker

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on May 13, 2007

SOURCE: whirlpool dishwasher

I had the exact same problem with my Whirlpool Quiet Partner IV. I removed the lower arm, and a couple of components below that, and got to the filter/grinder (that thing that chops up and filters the recirculated water before it goes to the pump that feeds the arms). The filter was completely clogged. I used a knife to scrap away the foodstuffs, put everything back together and all worked excellent. Just goes to show you that you should rinse your plates before to place them in the dishwasher.

Ad

Anonymous

  • 213 Answers
  • Posted on Nov 20, 2007

SOURCE: Bosch dishwasher problem

remove the kick plate below the door. youll see a white tray behind the kick plate. theres water in the tray thats activating a overflow switch. with a towel or 2 remove as much water from tray as possible. this will solve problem

David Shaub

  • 2994 Answers
  • Posted on Jan 03, 2009

SOURCE: water pours from the vent located on the sink near the faucet.

Make sure the 'T' where the dishwasher is connected is directing the water downward. also, if this isn't the issue, move the 'T' to the other drain pipe. If the 'T' is too close to the vent, you will get back pressure and it will come out. The less resistance the better.

Anonymous

  • 3 Answers
  • Posted on May 09, 2009

SOURCE: Diswasher Pump won't stop running

Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills, OK, then this ISN'T a solution to your problem.

I have a Bosch SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the water drained, but no new, clean water came through the hot water pipe. The drain just kept running, but nothing else happened.

Here's what happened. Under the main chamber of the dishwasher, by three inches or more, is a white plastic tray. It sits almost at the floor, and it may not be obvious that it's a tray capable of holding water. The overflow water spilled into that tray, which in turn caused a float in the far left side of the tray to lift (the way a toilet float lifts when the water fills in a toilet tank) and shut off the water intake valve (like the toilet float shuts off the toilet water flow). So long as that valve is closed, your machine will not run.

STOP: disconnect power supply at this point for safety.

To see the white plastic tray and thereby fix the problem, you'll need to take off the BLACK TOE-KICK (attached on my unit by two star-head screws at its bottom) and, possibly , the OUTER PANEL OF THE DISHWASHER DOOR (in my case, a custom wood panel (attached by a few screws through the inner side of the door, two screws that are accessed by popping off little--smaller than a dime size--covers on the sides of the doors, and then the door panel lifts up and out). (I took the outer panel off, but I can't remember if I would have had to reach into the white tray without doing so.)

Once you do that, you can see the white plastic tray. It doesn't come out--at least not without removing the entire machine--so try this. You can take your fingers and feel over and into the tray. You'll probably feel the water--I did. Look at the far left of the tray with a flashlight. Back there you'll see a flat, round, 3-inch diameter piece of white plastic sitting at the bottom of the tray. To its center is a generally U-shaped lever looking device, which, at its far left end, is connected to a red stick pointing up into the machine. When water goes into the tray, the float rises, causing the U-shaped lever to rise, causing the red stick to raise, which (though I couldn't see it) causes an electrical signal to run to, and shut, the valve for your water intake.

I took paper towels, and then a narrowly cut sponge, to sop up the water in the tray. I then took my shop vac and, using it as a blower, blew what little water was left right out. You might be able to use a hair dryer, but first sop out what you can or it'll take forever. Once you've done that, put everything back together and plug your dishwasher back in. My buttons are at the top panel. To reset, hold down the two buttons marked for clear drain for three seconds and release. You should be able to start up then. It took 15 seconds before the water started to run, but it did and the machine works fine again.

Interesting note: The valve that stopped the water from flowing in automatically opened once I got the water out of the tray. You don't need to reset the valve.

Good luck.

Montpelier Man

ginko

Ginko

  • 19396 Answers
  • Posted on May 21, 2009

SOURCE: Pump Runs On After Water Is All Drained Out?

If the cycle does not stop draining that is usually because of a faulty water level switch that controls the water level in your appliance.
The faulty sensor cause the machine to think that there is still water inside, even when water has drained completely.
Check if the floating sensor is stuck or faulty.
Some machine may use a membrane switch instead of a floater.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

699 views

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Cindy Wells

Level 3 Expert

6717 Answers

Brad Brown

Level 3 Expert

19190 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...