Question about Excalibur. K9-MUNDIAL-SS Entry Level Auto Alarm with Dual Zone Shock Sensor

1 Answer

Car does not start lights flash 3 times - Excalibur. K9-MUNDIAL-SS Entry Level Auto Alarm with Dual Zone Shock Sensor

Posted by trlramp on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 34 Answers

Can you be a little more specific. Are you talking about a remote starter???

Posted on Feb 05, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does airbag fault code 13 mean for the 1995 ford taurus?


Code 13 for ford has it as: air bag sensor or crash sensor problem. May need to take to dealership for fix.

Aug 01, 2016 | 1995 Ford Taurus

1 Answer

HOW TO FIX: CHECK LIGHT & O/D LIGHT FLASHING -Won't go off!


You mean engine light is on,turn three times the on and off do not start car,should flash light...two times =2-3 means code 24

Dec 03, 2015 | 1994 Toyota Camry

1 Answer

Airbag flashes 3 times then 2 times


Code 3 -Open circuit to drivers SRS airbag. This means in almost every case the rotating clock spring ribbon contact under the steering wheel is defective.

Oct 24, 2012 | 2009 Mazda MAZDA6

1 Answer

Hi Machine will no start..At first all lights flashing and now just start and reset button flashing.. Start button flashes 3 times reset button flashes 5 times. Can you help. Cheers


I have a zanussi zwf1432w aquacycle.

Hi Machine will no start.Starts to fill,Stops and goes straight to drain.There is no blockages in filter or pipes,Have checked all,Even pipe from drum to filter.

At first all lights flashing and now just start and reset button flashing..

Start button flashes 3 times
reset button flashes 5 times.

Can you help.
Cheers

Apr 05, 2011 | Washing Machines

2 Answers

How do you read the codes


2 ways. 1) with a code reader from autozone (they do it for free by the way). and 2) use the cars key by turning the ignition key on and off 3 time and the 3rd time leave it on. do not go all the way to start. don't crank engine. just on. wait a few seconds and the check engine light will start to flash the codes(or power loss light). it will flash the first digit then pauses for a few sec. and then flashes the second digit. must count the flashes and write them down. for example first 2 flashes means 2 pause then 3 flashes means 3. that is code 23. that may not exist but is just an example to let you now how it woks. good luck.

Sep 10, 2010 | 1990 Dodge Dakota

1 Answer

My nissan serena air bag light flashes on and of


"If you have the airbag light, it will show steady for a few seconds (the manual says 7 secs) after you turn the key from off to on (but not start) and then start to flash. Here is how to reset it:

1. Turn the key from off to on.

2. Watch the airbag light closely. It will stay on for a few secs. and then as soon as it blinks off (the start of the flashing), turn the key off instantly.

3. Count to 5 (1 Mississippi, 2 Mississippi . . . .)

4. Repeat steps 1-3 two more times until you have done the cycle three times.

5. Now turn the key on and watch the light. It will start blinking in a different, slower manner. This is diagnostic mode. You can watch this for a little while, no hurry.

6. Now turn the key off again, Count to 5 like in step 3 again, and turn back on. If the procedure worked, the airbag light will not be flashing.

If it does not work the first time, just repeat the steps again."

Aug 06, 2010 | 1996 Nissan 200SX

2 Answers

2003 grand am gt check engine light stays on


If you turn you ignition switch 3 times on and off(w/o turning the car on) the check engine light should start flashing. First it will flash so many times. Ex) 3 flashes, write down three. Then it will pause and then start flashing again. Ex) 4 flashes, write down four. Then there will be one final flash, JUST ONE. That means it is done. Now, if you wrote down 3 and 4 then your code is 34.
Each code has each separate error or faulty part in your car.

Oct 02, 2009 | 1998 Pontiac Grand Am

2 Answers

How do i reset the maintainance light on my 2007 trail blazer


  1. Turn the key to the "ON" position
  2. Press the accelerator all the way to the floor 3 times within 5 seconds
  3. You should see the oil light flash, once it stops flashing, turn the key off
  4. Wait 10 seconds before starting the vehicle, the oil light should now be reset
  5. If this doesn't reset the light, repeat steps 1-4 paying careful attention to pressing accelerator all the way to the floor 3 times within 5 seconds

Aug 12, 2009 | 2007 Chevrolet TrailBlazer SS

1 Answer

Will not start just died.


Engine? Those flashes should be 2 digit numbers . Cycle key, on, off, on, off, on & leave on & recount those flashes. Example: 3 flashes, pause, then 3 more is code 33. Or 2 flashes, pause, 4 flashes, is code 24. 5 flashes, pause 5 more, is code 55 which means end of message. Then get back.

May 31, 2009 | 1989 Dodge Caravan Cargo

Not finding what you are looking for?
Excalibur. K9-MUNDIAL-SS Entry Level Auto Alarm with Dual Zone Shock Sensor Logo

532 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dual Electronics Vehicle Parts & Accessories Experts

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Brad Brown

Level 3 Expert

18520 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Dual Electronics Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...