Mitsubishi WS-55511 55" Rear Projection Television Logo

Related Topics:

Posted on Feb 18, 2008
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Mitsubishi WS 55511

Does not come on and checked the DM module , No burn sign or Pop up cap. What is next???

Answer This Question
  • 2 more comments 
  • dstan May 07, 2008

    When I turn the tv on with remote, the green light stays on for 3 seconds,

    then goes off. There is no picture or sound. I unplugged it and left it alone

    for a day but still same problem.

  • Anonymous May 28, 2008

    unplugged my tv to clean behind it and plugged it back in to find the green light ( reset) flashing. Did what the manual said to do, then called mitsubishi and had no results. They are willing to send out a tech at my cost. They do not stand behind their product. I would like to know how to correct this problem without a service call.

  • ScottJon Jul 08, 2008

    my WS-55511 worked fine yesterday, nothing today


    I tried everything including calling Mitsubishi, but that was worthless.


    i saw the note above and after a full day of trying different things, I ran my finger across all the buttons and it started right up


    go figure, I Guess its time for a Panasonic Pasma

  • Anonymous May 11, 2010

    is the light on the front blinking.

×

1 Answer

Jose Garcia

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Vice President:

An expert whose answer got voted for 100 times.
Champion:

An expert who has answered 200 questions.

  • Expert 453 Answers
  • Posted on May 02, 2008
Jose Garcia
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Vice President:

An expert whose answer got voted for 100 times.
Champion:

An expert who has answered 200 questions.

Joined: May 01, 2008
Answers
453
Questions
0
Helped
92501
Points
112

Posible bad convergence with open pico fuse

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Ws-55511 green light changed caps. where is pico fuse located ?
There are at least two pico fuses in the DM unit along with the caps; DM is large metal box on left as you look from behind.

Blinking green light that does not stop means problem is in DM unit that is not booting up.

If you have questions let me know.

SD TECH
Read full answer
Sep 29, 2011 • Mitsubishi WS-55511 55" Rear Projection...
0helpful
1answer

Need to know where capacitors are on mitsubishi ws 55511 tv are located at have back of tv off and cant locate them please help thanx
they are located inside the DM modules case( Metal Case on far left side ) open the metal case and you will see 7 caps on the DM power board. I am posting a pic of the board with the 7 caps that need replacement use 1000UF 25V caps to replace the 1000UF 16V caps that are currently installed.

slinteriors_20.jpg
Read full answer
Aug 08, 2011 • Mitsubishi WS-55511 55" Rear Projection...
0helpful
1answer

The power outage went out yesterday and my tv wont turn on
Hi,
Most likely it is capacitors on the dm board that have gone bad. This is a fairly common problem and has been addressed on fixya many times. If you know someone who is good with soldering and technically incline or even an honest electronics guy then the repair is quite cheap. If you have any other questions please let me know. if its not the capacitors on the DM supply then its a problem with the whole DM assembly that part usually is around 300$. So you may want to consider purchasing a new tv. Trying the 7 caps on the dm supply board shouldn't cost much if it takes anything more then that. I would sell the tv on craigslist or ebay and recoup as much as you can towards your next tv.
thank you,
lee
Thank you,
lee
Read full answer
Apr 01, 2010 • Mitsubishi WS-55511 55" Rear Projection...
0helpful
1answer

On my WS-55511 TV, after a power interruption, will not power up. All i get is a continuos blinking green light.I tried unpluging the tv several times, no luck.
Good Day,

LED does not stop blinking after plug in. Check for 12 volts at connect or PF pin 10 and 28 volts at connector PF pin 11, (on the board on the right hand side, but on the left side of board towards the back of TV). If the supplies are correct suspect a problem in the DM Assembly (part # 955C230002). Part is not available for replacement.

Check C9B01, C9B02, C9B03, C9B13, C9B14, C9B17 and C9B18 (1000 UFD, 16V, 105C) on the DM Power PCB located within the DM Assembly. If they are bad or not, replace them all with part # 181P734030 (680 UFD, 16V, 105C).

The DM (Digital Module) Assembly is located on the extreme left of the chassis from the back. It is standing in a vertical position. Remove cover and you see the Cap’s in one corner of the inside PCB.

Good Luck, Big IRISH.
Read full answer
Dec 14, 2009 • Mitsubishi WS-55511 55" Rear Projection...
1helpful
1answer

Ws-55511 replaced all 7 caps in the dm, still wont power on
I have seen this only 2 times----you may be able to unsolder and remove the reset micro switch---you have to remove the whole screen to get at it---the micro switch board may not be available---the switches can be tested with a ohmmeter set to high end and of course should not have a reading across them--I bet the reset switch is bad--you can remove it and put the keyboard back---most of the Mitsubishi sets use the same type of switches--Only other thing is leave the keyboard disconnected and just use the remote.

Glad you found the problem.

Regards, SD TECH
Read full answer
Sep 14, 2009 • Mitsubishi WS-55511 55" Rear Projection...
0helpful
1answer

Ws-55511 DM 5volts draged down blinking led
Hello,

Did you check the caps on the DM board? They usually go bad after a period of time. Remove the DM board and the metallic cover and there should be 4 to 7 capacitors (There are different revisions of the DM board). Check these caps also, replace if needed.

Thank you,

Shuttle83

http://www.electron-age-technologies-llc
Read full answer
Apr 05, 2009 • Mitsubishi WS-55511 55" Rear Projection...
1helpful
1answer

Flashing power light tv wont come on mitsubishi 1080
If the tv has the continuous flashing led, you have a DM board problem. It is likely bad capacitors in the DM module.. there are 4 of them 1000uf caps that will go bad. They will get a bulging top on them when they go bad. . Mits recommends replacing them with 680uf caps with a comprable or higher voltage rating. The DM module in on the left side of the set (viewed from the back) and is somewhat difficult to remove.
Read full answer
Dec 03, 2008 • Mitsubishi WS-55511 55" Rear Projection...
0helpful
1answer

Mitsubishi rear projection tv won't turn on
know problem of bad caps.

http://www.chrisandnat.com/Projects/BlinkingTV/blink.htm
http://www.jeremyburns.com/Mitsubishi-Green-Blinking-Light-Fix.pdf
http://www.fixya.com/howto/h159332-mitsubishi_dm_board_repair
http://hdtvoice.com/voice/showthread.php?t=32186
replace DM

Picture of bad caps
http://www.auctioncreations.com/wd62525a.JPG

The DM board is the one with the digital connectors on the back panel. If you already have it appart, you may as well check the caps on all of the boards. The caps that go bad are typically Jamicon brand caps in 1000 uF and 330 uF values. There are also a couple of 3300 uF caps in the PS that cause problems.
Read full answer
Jan 08, 2008 • Mitsubishi WS-55511 55" Rear Projection...
0helpful
1answer

TV wont turn on
know problem of bad caps.

http://www.chrisandnat.com/Projects/BlinkingTV/blink.htm
http://www.jeremyburns.com/Mitsubishi-Green-Blinking-Light-Fix.pdf
http://www.fixya.com/howto/h159332-mitsubishi_dm_board_repair
http://hdtvoice.com/voice/showthread.php?t=32186
replace DM

Picture of bad caps
http://www.auctioncreations.com/wd62525a.JPG

The DM board is the one with the digital connectors on the back panel. If you already have it appart, you may as well check the caps on all of the boards. The caps that go bad are typically Jamicon brand caps in 1000 uF and 330 uF values. There are also a couple of 3300 uF caps in the PS that cause problems.
Read full answer
Oct 22, 2007 • Mitsubishi WS-55511 55" Rear Projection...
1helpful
1answer

Help my ws-55511 can anyone help me with this.

Changing caps on DM board is good prevent maintenance,

 but does not represent the solution...DM caps symptom is

 Continuos blinking light.

 

 See    " problem 351"    On 10/20   WS 55908  comments.

  Let me know....T.

Read full answer
May 16, 2007 • Mitsubishi WS-55511 55" Rear Projection...
Not finding what you are looking for?

View Most Popular

WS-55511 55" Rear Projection Television

  • Televison & Video

Related Question

Ws-55511 green light changed caps. where is pico fuse located ?

  • Mitsubishi WS-55511 55" Rear Projection Television

Related Topics

185 views

Ask a Question

Usually answered in minutes!

Popular Questions

Blinking Green Light on Mitsubishi DLP 52525

Mitsubishi WD-52525 52" Rear...

Tried convergance, but would work

Mitsubishi VS-55609 55" Rear...

Mitsubishi dlp tv WD65733 has white spots, like

Mitsubishi WD-65733 65" HDTV

65'' mitsubishi hdtv white dot on screen problem

Mitsubishi WD-65C9 65" DLP HDTV

What does a blinking orange light on my Mitsubishi

Mitsubishi WD-52531 Television

Check Out the Latest HD Televisions Report
Check Out the Latest HD Televisions Report

View all Fixya Reports

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1259 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...