My wii fit board won't connect with tv is the blue light suppose to stay on all the time or flash

It's either not establishing a connection with the Wii, or it's batteries need changing. I personally have never had to connect a balance board with the Wii for the first time, I only played with it at my friend's house.

I AM NOT GOING TO AWNSER YOU Q BUT I CAN TELL YOU THAT THAT IS THE SAME THING THAT IS HAPPING TO OUR SO IF YOU GET THE SOLUTION BY ANY CHANCE WILL YOU LET ME KNOW

there is a red button underneath the battery cover this is the sync button there is one on the wii console next to the sd card solt hold both of them and the same time until they are connected this will allow the wii board to stay on

follow this

1. Insert a Wii Balance Board compatible game disc in the Wii console.
   
   
   
2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.
   
   
3. Open the small SD Card slot cover on the front of the Wii console.
   
   
4. Remove the Battery Cover on the bottom of the Wii Balance Board.
   
   
5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.
   
   
6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.
   
   
7. The blue light will stop blinking and stay on steady once the syncronization is complete.

Hope this helps

Try these steps!


1. Insert a Wii Balance Board compatible game disc in the Wii console.


2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.


3. Open the small SD Card slot cover on the front of the Wii console.
4. Remove the Battery Cover on the bottom of the Wii Balance Board.
5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.
6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.
7. The blue light will stop blinking and stay on steady once the synchronization is complete.

please leave a good rating and testimonial if you appreciate my help. THNX

Make sure that you have synced the board to the wii (similar to a controller). You have to take the battery cover off the board and push the sync button. The blue light will start flashing. From there you need to open the front cover of your wii under the power button.

From there you start up wii fit and it will prompt you to turn on your board. You should get a solid blue light. If you don't, you may need to try syncing again.

It likely needs to be resync'ed since it hasn't been used in a while. The flashing lights show it is trying to connect to the Wii...if they never turn to a steady blue, it never connected. A sync should correct the problem.
First press the red "sync" button on the front of the console, then inside the battery door of the Balance Board. The results should be immediate. If the board never holds a steady blue light after trying to sync, you problem is something else that I couldn't guess!
I hope this helps!

test it on another wii, if you cant then call Nintendo support, it depends on the blinking really.. its probably doa... dead on arrival or something,..

The light does not need to stay on. It is supposed  to flash approx. 3 times, then go off. Though the light is out, the game balance board is still on.

Try these steps!


1. Insert a Wii Balance Board compatible game disc in the Wii console.


2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.


3. Open the small SD Card slot cover on the front of the Wii console.
4. Remove the Battery Cover on the bottom of the Wii Balance Board.
5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.
6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.
7. The blue light will stop blinking and stay on steady once the syncronization is complete.