Question about Crate Music

1 Answer

Crate Bass Amp B100 - No sound.

When turned on, LED indicator light comes on, but no output of sound. Tried: different bass, different cable, different outlet, new fuse.

Posted by janetbell222 on

Ad

1 Answer

Tim Swiercinsky

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,126 Answers

Do you happen to have another speaker that you could hook up to speaker output? This would bypass the amps internal speaker and lf you get sound from that setup, it would mean either a jack failure or possible internal speaker problems. Please let me know.

Posted on Jan 24, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Warwick xtreme bass amp no sound


get a new amp or try buying a new guitar i do not no ask the people
at gutair store sorry if i can not help

Mar 24, 2014 | Warwick Music Equipment Warwick XTreme 51...

1 Answer

No sound coming out for my hartke amps?


Are the internal speakers properly connected via the rear-mounted 1/4 inch "Speaker Output" jack? If so and still no sound, try connecting a separate external speaker (floor monitor, pa cabinet) for a "low volume" test.

The OM says the internal speakers are 4 ohm so it's unlikely that a wiring problem with speaker connections would cause all four to stop working. With AC power disconnected from outlet check for an internal speaker protection fuse BUT be careful. Charged capacitors can hold a charge for weeks!!!

Oct 25, 2012 | Hartke VX3500 Bass Guitar Combo Amplifier

1 Answer

My rumble 30 bass amp makes a lot of bad noise when i plug it in. it started off when i first started playing it and it worked fine, then after a few minutes it started making the noise. i've tried...


How new is the amp?

A single faulty solder can do that...I'd try returning in to the seller.
Have you tried a different amp with the same equipment?

Sounds like a wiring issue.

Hope I've helped
PvT

Sep 25, 2011 | Fender Rumble 30 30watt Bass Guitar Combo...

1 Answer

Hello! I recently bought used Behringer EQ 700, but it's not working. Baterry is ok, the red ligh is burning, when I press the pedal, but no sound is coming through, even when its not on. What could be...


The red light means NOTHING regarding the battery condition... If battery is not new, try a new one.

I have seen several problems... some people get the cables backwards for input and output. The INPUT cable is what turns on the battery and it has to be a mono cable.

ANOTHER common problem with ABUSED pedals is that the jack used for external power adapter gets smashed at some point and cracks the circuit board near it. USUALLY the light will not come on when this happens.

Byond this, it probably requires repair. Some are easy to open and others are a bear to get the circuit board out... key is to NOT force very much when working on these.

Feb 09, 2011 | Behringer BEQ700 Bass Graphic Equalizer

2 Answers

When i play a bit loud (not too much though just when the light blinks red on the hard play) the sirquit closes the amp for two seconds.can you healp me on this ?thank you very much


does your bass have active pick ups?
do the ratings on your amp match the ratings on your speaker?
are you using a pedal?
does your pedal have an output adjustment?
have the ground on your bass checked.
make sure you're using the right kind of cable.
and be sure that the outlet you're using is grounded.

Feb 08, 2011 | Ibanez P500H Promethean Bass Amplifier...

1 Answer

SWR WorkingPro 400 watt head - no sound, Preamp Clip red LED is continually lit, Limiter green LED continually lit - fuse is perfect. It worked for a few minutes, then just stopped.


Since the PA clip is not lit, the problem seems to be up front...

First thing is to look for a bad cable as a broken ground could be putting hum at a clipping level. First thing, test this by unplugging all inputs. If the clipping light goes out, then you have bad cables or a ground loop.

Try sending a line level signal into "Effects return" to test if the power amps are OK.

If the clip light is still on, turn all gain controls down to minimum. If light is still on then take unit for servicing.

May 31, 2010 | SWR WorkingPro 15 200 Watt 1x15" Bass...

3 Answers

Bass Guitar Keeps sound keeps cutting in and out.


There is an inconsistency in your text. You indicate that cables were swapped and problem still existed...
You said:... "i have tried using it on a different amp and still fine".

If you tried it on a different amp and it was still fine then the guitar is probably OK.

THEN your amplifier is in question as the root of your problem.

What is the amp you have? The guitar is the CB-42, but what amp do you have?

MANY intermittent problems with amplifiers are often with the input jack itself. These jacks are easily broken by tripping over a cable plugged into them.

Jan 04, 2010 | Fender Rumble 100 Bass Guitar Amplifier

Not finding what you are looking for?
Music Logo

Related Topics:

440 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crate Music Experts

Brad Brown

Level 3 Expert

18563 Answers

Ngoro

Level 3 Expert

2935 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you a Crate Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...