Question about Timex 1440 Nylon watch
I have searched high and low for instructions on how to change the time on my Timex 1440. It only has three buttons. One is mode, one is start/stop and the other is lap/rst. can you help as all the other watches seem to have four buttons.
In "Time Mode" when time is displayed, hold the "mode" button until the alarm flashes. Press the "mode" button again and the display should change to the seconds flashing. Press the st/stop button to change location between seconds, minutes, hours, date, month, and day. Use the lap/reset button to make any changes.
Posted on May 12, 2008
Setting My Timex 1440 Sports Watch (4-button)
This model (WR50M) has four buttons, from left to right, top to bottom: 1) Set; 2) Start/Stop; 3) Mode; and 4) Indiglo.
1. With the time and date showing, press the top left button.
2. Press the right top button (this sets seconds)
3. Press the bottom left button. This flashes the hour; press the top right button until you have the correct hour (there is no symbol for am, pm will show if pm).
4. Press the bottom left button, minutes flash. Press the top right button until correct minutes.
5. Press the bottom left button, month flashes. Press the top right button until correct.
6. Press bottom left button, date flashes. Press the top right button until correct.
7. Press bottom left button, day flashes. Press right top button until correct.
8. Press bottom left button, time format flashes (can be set to 24 hour clock). If correct, you're done. Press top left button if you're done (can be pressed at any step if you're finished).
To turn off the chime and alarm: Press bottom left until in the alarm screen. Then press the top right button repeatedly until the CHIME or CH symbol is gone and/or ALARM or ALM to disappear, then press the bottom left button to go back to main time.
Posted on Apr 16, 2008
If not in the time mode, press mode to get to the time mode.
While in the time mode, press and holdlap/rst for two seconds.
The seconds will begin to blink.
Press st/stop to reset seconds to zero
Press mode and the minutes will begin to blink.
Press st/stop to advance the minutes
Press mode and the hour will begin to blink.
Press st/stop to advance the hour
Press mode and the day and date will appear. The day will blink.
Press st/stop to advance the day.
Press mode and the month will begin to blink.
Press st/stop to month the minutes.
Press lap/rst to return to normal state with you new settings. You can hit lap/rst to return to normal state at any time in the process, for example if you only want to set the minutes, just hit lap/rst after you set the minutes.
Posted on Mar 12, 2008
Ok - i messed with this forever. i have some solutions, but not all.
* To get it off military time, do this:
while in time mode, hold down the "adjust" button (bottom right) and then press the "mode" button (top left). you'll notice that the "P" below the alarm time disappears and appears, just as the hours switch from military to non-military mode. (best to do this in the afternoon)
* You may find that the date gets weird looking after you mess with the buttons long enough. chances are it switched to European date mode, which places the day before the month (freaks). To switch back, hold down "start/stop" (top right) and then press "adjust" (bottom right).
Now if anyone can tell me how to set the date, I'll be psyched.
Posted on Mar 12, 2008
Setting the Timex 1440 Sports WR50M
Posted on Aug 01, 2009
Solution 5 worked for me as well!
Posted on Mar 20, 2010
Uh, yeah, its like, so easy! i have a purple sports timex 1440, and it has: mode, start/stop, set, and indiglo. it just broke at the kroc center. :(
i hope you find it easy. you just have to hold mode down until it blinks. press it again to go to the time. (the first time is the alarm) push start/stop to toggle, push start/stop again and again to go to the date, day, and then return to time. but if you do the alarm, you have to hold mode down again. i hope you can figure it out now.
i wish i could get my watch to work again. too bad it rusted. :(
remember, today is a time machine, what you do today will effect your future!
bye for now!
on wizard101, i am julia watersword. bye!
Posted on Jul 16, 2013
To set the time, all you need to do is press "set" as well as "start/stop" simultaneously. You need to ensure that you have got both buttons on at the same time and don't release it immediately. Once you press both of these buttons down, you need to keep it this way for at least a few seconds. Then, you will notice that the numbers on your watch face will start to flicker. The numbers that blink should be the numbers representing the seconds.
Once you have the numbers flickering, you can start setting or changing your time. You now have to use the "mode" button to change either the date or time on your Timex WR50M. Adjust the timing as to the number that you want to. Once you have done so, just press the "set" button and your timing and date has been adjusted. The process is really simple, isn't it?
Posted on Jun 02, 2012
Here is the user manual to the watch (or one very similar). Very explicit eacy instructions.
In this particular model:
1) Holding mode key for 2 secs will enter the adjustment mode.
2) Press mode button one more time to get to "time adjustment", annd then use the "start/stop" and "set" keys to adjust the time as usual.
Posted on May 15, 2008
None of the above worked for me, but did give me the clue of push the button and hold it down...On my watch, you Press and Hold the "set" button top left button. then the hours flash, you can press Indigo to change hours then set. Then minutes, indigo, then set.
Posted on Sep 26, 2011
then find the Timex module table directions to find the correct manual
Posted on Mar 16, 2011
This works [email protected]
Coordinated Universal Time (UTC) is the basis for the worldwide system of civil time. It is
determined using highly precise atomic clocks at time laboratories around the world that are
accurate to a billionth of a second per day. UTC time signals are broadcast via low frequency
signals. Your radio controlled Timex® watch synchronizes its time to the broadcast time signal.
PLEASE NOTE: This product only works in North America.
A. In TIME mode, press and hold SPLIT/RESET. Watch will attempt to synchronize time with
nearest time broadcast and tower symbol will flash in display. This may take up to two
B. Watch automatically attempts synchronization at 1:00 am daily and 4:00 am Sunday
C. Tower icon ( ) appears in display if synchronization has been successful within 24 hours.
WARNING: Depending on your location, the watch may be unable to pick up the radio signal
from Colorado. Synchronization may also not be successful if your watch is near a source of
interference (e.g., computer monitor) or you are in a building with a metal roof. Cloudy or rainy
weather conditions may interfere with radio signal transmission. If synchronization is unsuccessful,
try the following:
• Rotate watch 90 degrees.
• Move to a wall or window facing toward Fort Collins, CO.
• Move at least 2 meters away from any computer monitors.
• Move outside. If it works outdoors but not indoors, you may have a local interference
problem in your building.
If your watch is off by one or more hours: make sure you have properly selected your time
zone (see below). If you are in an area that does not observe Daylight Savings Time (DST),
be sure DST is disabled on your watch.
If your watch is off by a few minutes or seconds: make sure that your watch is currently
receiving the signal (tower icon appears in display).
If your watch did not adjust time for DST, make sure that your watch is currently receiving
the signal (tower icon appears in display).
QUICK START FEATURE: At any time, you can press and hold SPLIT/RESET to force watch to
For further information on synchronization/interference issues, visit the U.S. government
Posted on Mar 10, 2008
Tips for a great answer:
Aug 10, 2011 | Timex Watches
To set the time on your Timex 1440 Watch, please follow these directions:
1. Press and hold MODE (Upper left button)
(HOURS will flash and you'll be in Alarm Mode).
2. Press MODE again to enter TIME mode.
(SECONDS digits will flash.)
3. Press ADJUST (bottom right button) to set SECONDS to zero.
4. Press START/STOP (upper right button) to select MINUTES
5. Press ADJUST to change
6. Repeat to set Hours, Date, Month, and Day of the week.
(Go through 12 hours to set AM or PM)
7. Press MODE when finished
8. To display DATE from TIME display, press START/STOP
9. With DATE displayed, press and hold START/STOP, then press ADJUST to change display between DATE-MONTH
10. With TIME displayed, press and hold ADJUST, then press MODE to switch between 12 and 24 hour format.
I hope you are now able to set the time on your watch! If you appreciate these instructions, please remember to rate this post.
Apr 18, 2011 | Timex Watches
Jan 19, 2018 | Timex 1440 Nylon watch
Mar 16, 2010 | Timex 1440 Nylon watch
Dec 26, 2008 | Timex 1440 Nylon watch
Nov 22, 2008 | Timex 1440 Nylon watch
Mar 25, 2008 | Timex 1440 Nylon watch
May 29, 2007 | Timex 1440 Sports Quotient¿ 53612...
Mar 16, 2007 | Timex 5B841 Wristwatch
113,051 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: