Question about Whirlpool Cabrio WTW6600SBT Top Load Washer

1 Answer

When I start the machine it starts to fill up and then it stops and on the dial it displays F and I can't find my user guide help please>>>

Posted by dh50697 on


1 Answer

Jan McZeal

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 632 Answers

The F1 error code on Whirlpool Cabrio Top Load Washers means primary control failure . Check every wiring harness to the machine control assembly for any poor and loose connection. Clean the wiring harness connectors and terminals to ensure good connections.

Resolving F1 Error on Whirlpool Cabrio Top Load Washers

  1. Safety first. Unplug the machine.
  2. Remove the three hex-head screws from the rear of the console assembly.
  3. Lift the console assembly off the cabinet and disconnect the user interface wiring harness from the machine control board.
  4. Disconnect and clean every wiring harness connector and terminal on the machine control board. Ensure that all connections are good and tight.
  5. Reconnect the wiring harness connectors and reassemble the console.
  6. Replace the machine control board if the problem is not resolved.
  7. Pull the pressure transducer tube off the fitting on the machine control board.
  8. Remove the hex-head control board mounting screw.
  9. Lift the front of the machine control board, slide it out from under the clips at the back, and remove it.
  10. Install the new machine control board in reverse order of the steps above.
  11. Reinstall the console and secure it with the three mounting screws.

Posted on Jan 24, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bosch max 1000,turns on starts filling and then stops.Why?

please consult your user manual in the trouble shooting guide download it from the manufactures website its normally freeeric

Dec 19, 2017 | Bosch Washing Machines

1 Answer

I have no user guide for MFS35PNFTS and machine came up with error 11 fill problem and then I hit the big red button to see what that does and now have no display. How do I de activate the emergency...

Hello I will be happy to assist you please follow the next steps:
    • 1

      Push the "Pause/Cancel" pad two times.

    • 2

      Remove the washer's plug from the electrical outlet. Leave it unplugged for at least a minute.

      • 3

        Plug the washer back in.

      • 4

        Push the button for the desired cycle.

      • 5

        Push "Start."

    If the problem is not solve please let me know or If the display still shows "F11," call Whirlpool customer service at 866-698-2358.

    If this information was helpful please rate my service, this will help me to help others.Thank you very much

    Mar 13, 2012 | Washing Machines

    1 Answer

    Is there some other way of getting this machine to scan documents to e-mails? I had a friend do this once but can't remember how she did it.

    Yes, the printer can scan documents for emailing. You can use the Lexmark Imaging Studio to scan to email. Go to Start menu -> Programs -> Lexmark 3500-4500 Series -> Lexmark Imaging Studio -> E-mail. Select the Photo, Several Photos, or Document option. Click Start. Click Create E-mail to have your images attached to an e-mail message.
    For more information, you can refer to the Lexmark X4550 user's guide. For Windows, you can access the user's guide by going to the Start menu -> Programs -> Lexmark 3500-4500 Series -> User's Guide.
    You can also download your printer's user's guide for free from the Lexmark website. Click on this link Lexmark 3500-4500 User's Guide.
    I hope this information has been helpful. Thanks.

    Jan 06, 2011 | Lexmark X4550 InkJet Printer

    1 Answer

    I can't figure out how to scan a document?

    Detailed scanning instructions are available in the Software User#s Guide for your machine. The guide can be accessed through the ControlCenter or from the installation CD that came with the Brother machine.
    To access the Software User#s Guide from the ControlCenter (Windows):
    1. Click WINDOWS/START -> (ALL) PROGRAMS -> BROTHER -> XXX-XXXX (WhereXXX-XXXX is the model number of the machine) -> ControlCenter3. The ControlCenter3 application will be loaded in the Task Tray near the system clock. (It appears as a blue square labeled CC3.)
    2. Double-click on the ControlCenter3 icon located in the Task Tray to launch the program window.
    4. Click USER#S GUIDE. A separate window will appear displaying the available user guides.

    Nov 01, 2010 | Brother MFC 240C All-In-One InkJet Printer

    1 Answer

    How to specify fax machine to dial '9' before fax number?

    Hello ilay,

    This procedure is from the Brother FAX-4100e FAQ link:

    Storing Speed Dial numbers:
    You can store Speed Dial locations on your machine(*). Once you have programmed the Speed Dial number on your machine, you can dial the number by pressing Search/Speed Dial, #(Pound Sign), the Speed Dial number, and then Fax Start.
    *The number of locations you can store varies by machines. Please refer to the User's Guide for your machine. The latest User's Guide is available in the Manuals section.

    To store Speed Dial numbers follow the steps listed below:

    1. Press Menu.
    2. Press the left or right arrow key to select Fax and press Set.
    3. Press the left or right arrow key to select Set Auto Dial or Set Quick Dial, and press Set.
    4. Press the left or right arrow key to select Speed-Dial and press Set.
    5. Use the dial pad to enter the location (Speed Dial number) where you wish to store the number and press Set.
    6. Enter the number you want to store (up to 20 digits) and press Set.

    If you want to enter a pause in the dialing sequence (to wait for an outside line, for example), press Redial/Pause as you're entering digits. Pressing Redial/Pause enters a 3.5-second pause when the number is dialed, and a dash appears on the screen. If you need a pause longer than 3.5 seconds you can press Redial/Pause as many times as needed.
    7. Use the dial pad to enter the name or company name (up to 15 characters) and press Set.
    If you want to store the number without a name, just press Set.
    8. Return to STEP 5 to store another Speed Dial number or press Stop/Exit to exit the menu.

    [Here's the web address for the Brother FAX-4100e FAQ]{30FA9470-D303-4B5B-8BDC-89B1CBA491AE}&NRORIGINALURL=%2fBSC%2fpublic%2fus%2fus%2fen%2ffaq%2ffaq%2f000000%2f002000%2f000004%2ffaq002004_010.html%3freg%3dus%26c%3dus%26lang%3den%26prod%3dfax4100_us&NRCACHEHINT=NoModifyGuest&prod=fax4100_us%C2%AE=us&c=us&lang=en#one_7

    [Here's a link to the FAX-4100e users guide]

    If this solution is helpful please click a thumbs-up rating below.

    Have a great day,

    Feb 10, 2010 | Brother IntelliFax-4100e Fax

    1 Answer

    I have i-mate jama 8050, i can't make call from my mobile,my mobile can call only the contacts which are saved in sim,but not calling on the number which is not in contacts list, please help me,

    Your mobile has been programmed to only make calls from your contacts. This is controlled in your settings menu under 'Fixed Dial'. (or similar command). You will need to change this setting.

    I do not have a copy of the user guide for your phone but for most phones these are the directions:

    When you turn on fixed dialing, you
    can call only numbers stored in the
    fixed dial list.
    Turn fixed dialing on or off:
    - > Settings > Security > Fixed Dial
    Use the fixed dial list:
    - > Settings > Tools > Dialing Services
    > Fixed Dial

    Jan 26, 2010 | i-mate Jama 101 Smartphone

    1 Answer

    I have Samsung fax & copy machine, SCX 5312F,

    Press "Menu / Exit", then "System Data" on the one-touch dial keypad. The display shows the first system data option "Cassette Paper" on the upper line of the LCD display. Scroll through the options by pressing ^ until you reach the option "Message Conf." Then press < or > to select your choice. Options are: ON, OFF or ERR (prints only when a transmission is not successful). When the desired selection is displayed as indicated by the blinking cursor on the lower line of the LCD display, press "Mode / Enter" to save the selection. Press 'Menu / Exit" to exit the menu or "Stop / Clear" to return to standby mode.

    Source: Samsung Laser Facsimile User Guide - Digital Laser MFP - SCX-5312F, pages 6.2, 6.4 and 6.5

    Jun 12, 2009 | Konica Minolta bizhub C250 All-In-One...

    2 Answers

    Error code e30 see user guide .comes on and stops washing do not have user guide

    E30 is a motor problem which is most likely brushes need replacing.
    Hope this helps & Thanks for using Fixya.

    Jan 18, 2009 | Washing Machines

    1 Answer

    Washing machine does not stop filling

    Does the machine start working normally after turning the wash cycle manually ?

    Feb 15, 2007 | Roper RAS8445KQ Top Load Washer

    Not finding what you are looking for?
    Whirlpool Cabrio WTW6600SBT Top Load Washer Logo

    189 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Washing Machines Experts


    Level 3 Expert

    85239 Answers

    Michael Thomas
    Michael Thomas

    Level 3 Expert

    3053 Answers

    Brad Brown

    Level 3 Expert

    18397 Answers

    Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides