Question about Denon AVR-1804 Receiver

2 Answers

Stuck on standby

I been using my denon amp for 2 years now and yesterday While I was watching a movie the sound went POP! and the amp went into standby mode.
I let it cool down and turned it back on and it goes striaght into standby,I then turned it on via the remote and it starts to work normally but after a few seconds goes back to standby.
I tried holding down the A& B buttons but still reverts back to stand by
Any idea,s
Thanks mark

Posted by on

  • zawdie Apr 30, 2008

    I have the same problem but i am in Jamaica! Shipping is NOT economical! What should i do now? I can't find the remote to see if it would start working again either. Any suggestions? How much would it generally cost to fix this problem?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How much should this problem cost to get diagnosed & fixed??

Posted on May 04, 2008

Ad

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 67 Answers

Unit is in protect mode there are a few problems that can trigger protect mode the most common is blown channel (shorted outputs). Sometimes one of the 15v regulators may go bad causing imbalance of supplys triggering protect mode. Also sometimes a bad solder connection could cause unit to go into protect also. I work for Denon authorzied repair center in Michigan if your nearby and Shipping to Michigan is economical let me know [email protected]

Posted on Feb 15, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuck on standby mode


Sounds like it might have a blown amp channel. Best to have a pro look at it.

Jun 18, 2013 | Denon AVR-1912

1 Answer

My Denon AVR-75 seems to stay in standby (red standby light is on) and I don'd get surround sound through it. How do I get it out of standby?


if the receiver does not power on from standby there is a problem like bad power supply or even bad macroprocessor. You need to bring it to a service center for diagnosing. 10-years old receiver, maybe better to buy new one.

Nov 23, 2011 | Denon AVR-75

1 Answer

Problem getting the best surround sound when watching a dvd


THE BEST SOUND IS WHAT SOUNDS BEST TO YOU, HOWEVER DO THIS:
1, USING THE SETUP MIC CONFIGURE YOUR DENON, PAGE 8 OF THE MANUAL. NEXT
2. RAISE THE REAR SPKR LEVELS, PAGE 46,47. NEXT
3. WHEN LISTENING TO AUDIO CD OR RADIO TRY THE 5 CH STEREO DSP MODE.
4. WHEN WATCHING A DVD USE DSP DOLBY PROLOGIC OR TRY 5CH STEREO IF THE MOVIE IS MOSTLY TALKING.
5, TRY 5CH STEREO WHEN WATCHING PROGRAMS WITH MOSTLY TALKING

Mar 01, 2009 | Denon AVR-2106 Receiver

1 Answer

Denon dvd 2910 locked up


You will have 2 choices here, replace it or have it repaied

Jul 06, 2017 | Denon DVD-2910 DVD Player

1 Answer

Denon AVR 2106 amp failure


Does it still power up for a little bit or so with no sound what so ever?....I there is no dents in it or metal pushed in causing cracked connector boards....I can take it off you hands for a couple parts I need ...because your transformer and 2 resisters are shot and it will cost almost as much as the unit cost's.

I do have a brand new never opend $649.99 Denon AVR-788 for $365.00.
And 2 used AVR units Denon and Onkyo.....ALL HDMI

call 630 742 6587

Aug 30, 2008 | Denon AVR-2106 Receiver

1 Answer

Sound is working only in mode PURE DIRECT


TRY PUTTING DVD PLAYERINTO ANOTHER DIGITAL IN PUT, ALSO CHECK DVD OUT PUT IS STILL BITSTREAM.
IFF YOU STILL HAVE A PROBLEM CHANGE THE CABLE,AND IFF IT STILL FAILS 2 WORK TAKE AMP 2 YOUR DEALER.

HOPE THIS HELPS.

CABLE GUY.

May 19, 2008 | Denon AVR-4802 Receiver

1 Answer

No sound


1. check if the amp is in PROTECTION mode (might be a bad speaker or shorted output)
2. check the 'MUTE' switch
3. try to use the FM/AM mode to isolate an input source. If there is sound then check input source.
4. ...still no sound have a techinician check it.

Apr 15, 2008 | Denon AVR-2400 Receiver

1 Answer

Denon AVR 2802 - Unit Turning Off


If DIGITAL sign blink, this mean DSP board is defective. It will cut the sound on the AMP section. DSp is maybe defective.

Jan 12, 2008 | Denon AVR-2802

Not finding what you are looking for?
Denon AVR-1804 Receiver Logo

1,713 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76237 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...