Password Recovery for Cisco Catalyst 4506 - Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

Question 1

0helpful

1answer

Cisco 3750 password recovery

Read this: http://www.cisco.com/c/en/us/support/docs/switches/catalyst-2950-series-switches/12040-pswdrec-2900xl.html

Must be helped for you! and more information about the Cisco 3750, please visit:
http://www.3anetwork.com/cisco-catalyst-3750-switches-price_c41

Feb 17, 2014 • Computers & Internet

0helpful

1answer

Need to replace the Chassis of CISCO 4500 switch. Can i know Step by Step procedure to do this change.

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/installation/guide/78-14409-08/04replac.html.......................... please follow the above link

Feb 11, 2011 • Cisco Catalyst 4506-E Cat4500 E-series...

1helpful

1answer

I just replaced cisco 4506 with new 4506-e, the uplink port didn't work for trunking

Hi, if you installed a Supervisor 6L-E 10GE (X2) in the new 4506-E and you want to use the two 10GE uplinks as Gigabit, you need to type in the following config lines:

hw-module module 1 port-group 1 select gigabitethernet
hw-module module 1 port-group 2 select gigabitethernet

Jan 17, 2011 • Cisco Catalyst 4506-E Cat4500 E-series...

0helpful

1answer

Hello, I tried the steps you have mentioned in the link below: http://www.fixya.com/support/t3932749-password_recovery_cisco_catalyst_4506 and the other similar resolutions on the cisco website but...

Please make sure you have only one supervisor module installed on your switch or else pull out the backup sup module and do this activity .

In the last step of reset it will ask to save the config.

do you wish to save this configuration? y/n [n]: y
You must reset or power cycle for new configuration to take effect

do not forget to type in y there.

Jan 01, 2011 • Cisco Catalyst 4506-E Cat4500 E-series...

0helpful

1answer

How to speed changed in gigabitEthernet 2/1 from cisco 4506switch

Hi

Ok so once you have logged into the router you do the following

go into enable mode by tyoing in en
Then type in conf t
then type in int X where X = the interface
then type in speed 100
then type end

This will set the interface to 100mbps

Feb 27, 2010 • Cisco Catalyst 4506-E Cat4500 E-series...

0helpful

1answer

Hi, what's a password on the router Cisco Catalyst 2960 default?

Try using username (none) pass public/private/secret or
cisco - cisco, ADMIN - changeme, pixadmin - pixadmin, root - attack, superuser - superuser as username - password. These are the defaults credintials for the Cisco routers.

Stelios.

Feb 22, 2010 • Cisco Rf Catalyst 2960 24-PORT 10/10

0helpful

2answers

How to enable dusable port error disable status

shut down the port and then no shut the port.

Nov 04, 2009 • Cisco Catalyst 4506 48-Port Switching...

0helpful

1answer

Default pasword

Cisco switches dont have a default password.
You will have to perform a password recovery process that is quite extensive.
You need to console into the switch using hyperterminal or teraterm and follow these instructions located at: http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

Dec 13, 2008 • Cisco Rf Catalyst 2960 24-PORT 10/10

0helpful

1answer

Hello

Hi
How can we help?

Nov 14, 2008 • Cisco Catalyst 4506 48-Port Switching...

0helpful

1answer

Problem with module WS-X4548-GB-RJ45V in Catalyst 4506

use software advisor in Cisco website to verify it.just follow the process.

console to it and show diag and see whether it detectable or not.

hope this help.

Dec 02, 2006 • Cisco WS-X4548-GB-RJ45V= Expansion Module

Question 2

Anonymous

Expert 121 Answers
Posted on Feb 19, 2010

Anonymous

Expert

Joined: Feb 19, 2010

Answers

121

Questions

0

Helped

67943

Points

308

Please see Cisco's page at http://www.cisco.com/en/US/products/hw/routers/ps5199/products_password_recovery09186a0080093e12.shtml
for step by step details and more in depth instruction.

1. Reboot
2. Press the "break" button on your keyboard within 60 seconds of the power-up to put the router into ROMMON mode.
3. confreg 0x2142
4. reset
5. type, "no" when prompted to enter the initial configuration dialog.
6. enable
7. copy startup-config running-config
8. conf t
9. enable secret <password>
11. config-register 0x2102
12. reboot again

Related Topics:

Trustworthy Expert Solutions

Password Recovery for Cisco Catalyst 4506 - Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Cisco 3750 password recovery

Need to replace the Chassis of CISCO 4500 switch. Can i know Step by Step procedure to do this change.

I just replaced cisco 4506 with new 4506-e, the uplink port didn't work for trunking

Hello, I tried the steps you have mentioned in the link below: http://www.fixya.com/support/t3932749-password_recovery_cisco_catalyst_4506 and the other similar resolutions on the cisco website but...

How to speed changed in gigabitEthernet 2/1 from cisco 4506switch

Hi, what's a password on the router Cisco Catalyst 2960 default?

How to enable dusable port error disable status

Default pasword

Hello

Problem with module WS-X4548-GB-RJ45V in Catalyst 4506

Not finding what you are looking for?

Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

Cisco 3750 password recovery

Ask a Question

Check Out the Mobile Browsers Report

Top Cisco Computers & Internet Experts

Brad Brown

Grand Canyon Tech

Sean Wright

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Trustworthy Expert Solutions

Password Recovery for Cisco Catalyst 4506 - Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Cisco 3750 password recovery

Need to replace the Chassis of CISCO 4500 switch. Can i know Step by Step procedure to do this change.

I just replaced cisco 4506 with new 4506-e, the uplink port didn't work for trunking

Hello, I tried the steps you have mentioned in the link below: http://www.fixya.com/support/t3932749-password_recovery_cisco_catalyst_4506 and the other similar resolutions on the cisco website but...

How to speed changed in gigabitEthernet 2/1 from cisco 4506switch

Hi, what's a password on the router Cisco Catalyst 2960 default?

How to enable dusable port error disable status

Default pasword

Hello

Problem with module WS-X4548-GB-RJ45V in Catalyst 4506

Not finding what you are looking for?

Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

Cisco 3750 password recovery

Related Topics

Ask a Question

Popular Questions

How to reset the cisco switch to factory default?

Fails post test: POST: Inline Power

No internet linksys connected to catalyst 2900 XL

Sending DHCP request across diffrent vlans

''!!! WARNING: The switch is not usable !!!''

Check Out the Mobile Browsers Report

Top Cisco Computers & Internet Experts

Brad Brown

Grand Canyon Tech

Sean Wright

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Manuals & User Guides