Question about Kenmore HE2 Plus Front Load Washer

2 Answers

Error codes I get a "D5" error code on my kenmore washer HE2plus. what is it?

Posted by kornsbtch on

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Kenmre HE2 Plus front loader has a F 28 error. Whats the problem and how do I fix it?

Posted on Jan 20, 2010

Ad

EYAD

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 1 Answer

Kenmre HE2 Plus front loader has a F 8 error. Whats the problem and how do I fix it?

Posted on Sep 23, 2012

  • EYAD Sep 23, 2012

    I POT THE WOSHERES IN 220 V AC I MISS THE TRANSFORMER 115 VAC

×

Ad

1 Related Answer

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: I have a Kenmore frontloader washer HE2Plus that says error code

"F20" is a No Water Detect error. It is an indication that you either have no water coming into the washer, or very little water at all. If the pressure switch has not tripped after 6 minutes, the error code is displayed. This can be a potential problem with the following:


If you have NO water in the wash tub, check the following:

- Inlet water valve may be clogged. Clean inlet screens if necessary.
- Make sure water taps are on.
- Check inlet hoses for kinks or clogs.

If you HAVE water filling the wash tub, check the following:

- Make sure you don't have a siphoning problem. Click the following link for instructions:


http://www.fixya.com/support/r587481-prevent_washer_siphoning

- Verify Drain Pump operation.
- Verify the Pressure Switch hoses are intact and connected properly.
- Verify wire harness connections at the pressure switch, inlet valves, drain pump and Central Control Unit (CCU).

To access the Drain Pump - UNPLUG the washer and take the lower panel under the door off by removing the three screws under the bottom edge. HINT: Propping the front feet of the washer up can make access much easier. I use a couple small blocks of wood. With the screws removed, the panel should drop down then come off. If it sticks, tap either side and it should come free. The pump is located directly under the wash tub in the front of the washer. Verify the electrical connections are good and that the pump is running. Click on the following link to check the pump for obstructions:

http://www.fixya.com/support/r385845-checking_drain_pump_in_whirlpool_duet

To access the Pressure Switch - remove the three screws in the top panel along the back of the washer. With the screws removed, the panel should slide back, then, lift off. The pressure switch is located on the right-hand side of the washer in the rear. It is a round plastic device with electrical connections and a plastic air hose attached. Verify the electrical connections are intact, and the air hose is attached and not cracked or leaking.

To access the Central Control Unit (CCU) - with the top panel of the washer removed, the CCU is located directly behind, and just above the rear of the wash tub. There should be a tech sheet directly behind the lower panel or attached to one of the interior cabinet walls. Please refer to this sheet to learn how to perform diagnostics and to verify the wire connections at the CCU. In addition, the tech sheet will also assist in how to locate the components mentioned, and the specific measurements required determining if the components are good or bad.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 23, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

5d error code kenmore he2plus


Here's a video prem mathew suggested as a solution to your problem from YouTube:


Kenmore He2 washing machine washer drain problem fixed

Apr 26, 2013 | Kenmore Washing Machines

1 Answer

Kenmore he2plus what's troublecode f-21


F21 on the tech sheet says Long Drain If the drain time exceeds 8 minutes the water valve turns off.
NOTE: After 4 mins the "Sd" error will be displayed then 4 mins later the f/21 error code will be displayed.
Press Stop two times to clear the display.

(Solutions:) Check drain hose
unplug washer and check electrical connections at pump
Check filter for foreign objects
If these fail it says to replace pump.
12_11_2011_2_00_43_am.jpg

I’m happy to help further over the phone at https://www.6ya.com/expert/geneva_f6ab09a476387fe3

Dec 11, 2011 | Kenmore Washing Machines

1 Answer

Code D5, what is it?


A d5 error code usually means Sd. This error code is displayed when the control detects the basket has not seated on the hub or that the pressure switch has detected a Suds-lock condition. The washer will try to run a mini-clean out cycle using cold water and a 5 minute pause to clear the suds. If this cycle does not clear the display and complete the cycle the clothing may need to be rinsed by hand and then rewashed. The fault is caused by using the wrong detergent or excessive amounts of detergent.

Note: If the Hard Reset does not work, there may be an internal failure with the washer.



richroth.gif

Dec 11, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

F-21 error code, washer stops


Hi,

Check for the drain hoses(both sides of the pump) and check for a blockage,then check the pump for blockage,there should be 4 impellers on this pump and they can get broken off by coins and debris.
Thank you !!

Jul 13, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have a F-01 fault code on my Kenmore HE2plus front load washer. model # 11047512601. Sears talked me thru the software resets and still had the F-01 error. do I need to replace the Main Control Unit?


Hi,


The F01 fault code is indicating an EEPROM error or a PUMP DRIVER error. A communication error between the Central Control Unit (CCU) and the EEPROM on board the CCU occurred.

Possible causes of an EEPROM error:
A power glitch may have caused this error. Unplug the power cord for 3 minutes then reconnect power.

Possible causes of PUMP DRIVER error:
The pump driver fails to activate. Replace the the CCU board.
Most likely the CCU board will need to be replaced.

Thank you !!

Jun 28, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have a Kenmore He2plus washer that gives me an error of F33


Hi,

"F33" means that the CCU has not received a signal to shut off the water which would be sent by the pressure switch. The flow meter has signaled that the tub has received 10.5 gallons the CCU then shuts off the water and pumps the water out, giving the F33 error code.

Thank you !!

Jun 19, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

F21 error on kenmore he2plus washmachine. Door locks. Due to no spinning and water remaining in the machine? I run the rinse/drain&spin program (15 minutes) several times. it stays at 15min remaining...


"F21" is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a "SUDS" error may also be displayed. This may be an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:


1.First, attempt to unplug the washer for at LEAST 30 minutes to reset the Central Control Unit (CCU). Sometimes this is all that is required to correct momentary glitches with the unit. If the error code returns, proceed to step 2.
2.Check the drain hose to make sure it is not kinked or clogged.
3.Check the electrical connections to the pump and ensure the pump is running.
4.Remove the drain pump filter and check for foreign objects and/or debris.


If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 23, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

He2plus does not drain and spin


code F24
WATER TEMPERATURE SENSOR ERROR

next information is only for the TECHNICION

If the water temperature sensor NTC value is out of range (23 F to 217 F to 103F C) during the water-heating step of the WASHcycle.
NOTE:To find corrrect Ohm reading refer to the water temperature sensor in TECHNICION ONLY section.
Possible couse/Procedure
1.- Unplug washer or disconect power.
2.*check the water senser and conection to it.
3.-check resistence of heating element, if present on this model(abnormal=indifinity)
4.-refer to the water Temperature Sensor section

Am sorry but F7 error code is not in the information system.


"Was this helpful?"

May 11, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

F-33 code


The F33 error code indicates a pump drive system error. If the pump ohms out correctly & the harness is secure I recommend replacing the CCU (central control unit).
Please see the following image provided for instructions.

http://media.fotki.com/1_p,stwwfrggtqfbrbbxgtqsskgwtqkq,vi/wgtbwqwssxsbwkbdtfwxrbfbddwwf/1/1303472/5961857/image9159087223444281043img-or.jpg

Remember to disconnect power to the washer before attempting access.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Feb 16, 2009 | Kenmore 46462 Front Load Washer

1 Answer

Kenmore he2plus washer


Error F 28 is your heater and it will not unlock because of it.
http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=1176579&PPStack=1
Here is the part info thanks

Sep 21, 2008 | Washing Machines

Not finding what you are looking for?
Kenmore HE2 Plus Front Load Washer Logo

1,754 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Paul Carew

Level 3 Expert

3530 Answers

Nicola Conroy

Level 3 Expert

1428 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...