Question about Avanti EWC-12 Wine Cooler

1 Answer

Avanti EWC-12 circuit board replacement (correction)

Avanti sent me a new circuit board to replace that one that failed but they did not send instructions on where to solder the wires to the board. I can see where the red and black wires will go but am unsure of where the green and yellow wire is to be soldered. The board is a HYS60-12-KD V-0 130C. Any help you can provide will be greatly appreciated.

The colors of the wires were incorrectly stated on the last post. The red and black (power) wires were listed as red and white. The green and yellow wire was listed as two wires, green and white. It is actually only one wire that is green and yellow.

Posted by rick257 on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 49 Answers

The green an yellow wire is a ground. Look for an area on the board with a ground symbol Avanti EWC-12 circuit board replacement (correctio - earth.gif. Can you not match the location from the old board???
Either way the black and red are your positive and negative power, while the third is the ground. The wire probably are located in close proximity to each other.
Let me know if this helps

Posted on Jan 16, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can I get an electrical schematic

Google (Avanti)(EWC-12)(schematic) without parens, of course.

May 24, 2016 | Avanti EWC-12 Wine Cooler

1 Answer

Bring temperature down

What's the quickest way I can bring down my child's fever from 103 to 99 at least

Apr 07, 2014 | Avanti Products Avanti EWC-1201

1 Answer

Hys60 12 kd 130c circuit

Hi, This is very easy designer this Board, I 'm a repair center from this boards.... what do you need from shematic this board, question for my and I give help for you from Brasil in

Jun 21, 2013 | Avanti EWC-12 Wine Cooler

1 Answer

My avanti AT480 wont work. The console lights are on the safety key is on but when I press start nothing. I havnt used it for a long time. Do I need to reset but I cant find the reset button or something...

Unfortunately you may need a new console circuit board. I have just replaced 3 for the same treadmill model. It seems to be a slight problem with this model.

Feb 26, 2013 | Avanti Exercise & Fitness

1 Answer

My avanti wine chiller mod ewc 16 b serial n.0800854 stop cooling what can i do ?

I've added a link for an Avanti ewcb, There you can find a complete manual on the product which will help you to locate where the problem is coming from. hope I've helped!

Oct 24, 2012 | Avanti EWC16B Thermoelectric Wine Cooler...

1 Answer

Take apart AVANTI

here is the reference manual for that model hope it helps

Apr 22, 2012 | Avanti EWC-12 Wine Cooler

1 Answer


I have the same E4 problem. You can order the PCB from Avanti at Miami Florida or your regional Avanti service rep.

Jun 04, 2009 | Avanti WCR683DZD Stainless Steel Wine...

2 Answers

Avanti 12 bottle wine cooler...switch is bad. Electricity going to the switch but not turning on. Where do we get one? Avanti is NO HELP!

There is a circuit board in this that you'll have to replace,and good luck finding the part.Most of these coolers were built as throw aways,meaning when it stops working you, throw it away.

May 29, 2008 | Avanti Refrigerators

1 Answer

Replaced flash circuits

There can be two schools of thought for this.

When replacing the circuit board in a flash, this means that the lamp, photocell, LCD display, and the switch pads are the old ones. I would guess the main power inverter board is being changed.

What usualy fails on this board is the main electrolytic capacitor. Not always, but other parts can fail. If it is only the main capacitor, this can be bought at most any major electronics parts distributor. You only have to specify its value in MicroFarids, the mechanical size so it will fit, the lead configuration, and the Voltage rating.

As long as the voltage rating for the new one is the same or greater, and the size configuration is close, the new cap would most likely work. This type of cap is not very expensive compared to the cost of a complete board.

If other parts are also defective on the board, it may be impossible to service unless the part is a generic type. If the part is an SMD surface mount type, depending on the configuration, someone who has SMD soldering tools can replace the part.

I have repaired about 80% of the problems in photo flashes. I only send them out if the fault requires a complete board change or factory calibration. With a new board, calibration will probably be necessary.

Bottom line for me: I would buy new flashes if I had to pay out more than 60% of the cost of a new replacement. But, that is my personal view.

Jerry G.

Apr 17, 2008 | Nikon Speedlight SB-800 TTL Flash

Not finding what you are looking for?
Avanti EWC-12 Wine Cooler Logo

Related Topics:

2,050 people viewed this question

Ask a Question

Usually answered in minutes!

Top Avanti Furniture Experts


Level 3 Expert

8597 Answers

ray gallant

Level 3 Expert

68584 Answers

Tom Chichester

Level 3 Expert

56002 Answers

Are you an Avanti Furniture Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides