My rca projection tv has blue and green images like a 3D picture would without your 3D glasses, a double vision image and no other colors

Looks like the focusing lens may have moved a bit or the projector lamp has gone weak. Get a technician to check up the projector.

There's very little you can do here.

Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems.





SOLUTION #1

For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.


TV set after fluid change



SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

convergence amps bad, also check resisters burnt

All projection TV sets have two very common problems. One is convergence ( 3D/Warped video or dead set) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. In some cases the TV will also not show any video. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems.






Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.


TV set after fluid change



SOLUTION

You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here

projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems.






Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.


TV set after fluid change



SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems.






Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.


TV set after fluid change



SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems.






Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.


TV set after fluid change



SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

This tv have convergence problems,it dead.Red,green,blue misaligns colors,have colors shadows,3d colors pic like.All these problems are the convergence board have 2 STK convergence ICS some or all it resistors are dead.These parts must change to solved convergence problems.The shop will cost u $300-350 for parts and labors.

Ur convergence it dead,U know how to solder right?Tries buy a convergence kit use what in that kit.Tries these websites.Tv Repair World.com,Ebay.com.

its in your LCD connector re-connect it properly.