How to change the fuel hoses - Poulan Garden

check o2 sencer and vacuum lines to much air will cause run lean. code is cylinder bank 1 running lean.

remove fuel pump relay run engine till it stops (no fuel pressure in line remove clamps with hose clamp pliers wqe7ruull fule lines from filter then undo the clip at the other end of the two short pieces of fuel line and discard insert the two new pieces of fuel line in the kit put the 4 hose clamps on the new fuel hoses 2 on each insert the filter into the flexible hoses and refit the two hose clamps replace the fuel pump relay turn on ignition and wait for fuel pump to stop
start engine + check for fuel leaks at filter or hoses

Hi, welcome to FixYa.com my name is Shawn and I will be answering your question.

1. Relieve the fuel system pressure. Refer to the procedure in this section.

1. Disconnect the battery ground cable (14301) .

1. Drain the fuel from the fuel tank (9002) . Refer to the procedure in this section.
   
   Fuel Tank and Related Components

1. Raise and support the vehicle.

1. Remove the two pins from the fuel tank front protector.

1. Remove the three fuel tank front protector bolts and remove the fuel tank front protector.

1. Disconnect the evaporative emission hose (9E325) from the evaporative emission valve (9B593) .

1. NOTE: Label the fuel return line and fuel supply line to ease installation.
   Loosen the fuel return hose clamp and slide it away from the fuel return hose connection.

1. NOTE: Use a rag to prevent fuel from spilling while disconnecting the fuel lines.
   Disconnect the fuel return hose at the fuel tank .

1. Loosen the fuel supply hose clamp and slide it away from the fuel supply hose connection.

1. Disconnect the fuel supply hose at the fuel tank .

1. Disconnect the fuel pump and bracket electrical connector.

1. Loosen the hose clamp from the fuel tank to filler pipe hose (9047) and slide the hose clamp toward the fuel tank .

1. Separate the fuel tank to filler pipe hose from the fuel tank filler pipe (9034) .

1. Place a jack under the fuel tank to support it when the fuel tank support straps are removed.

1. Remove the two fuel tank support strap bolts and allow the fuel tank support straps to hang down.

1. Remove the spring clips from the fuel tank support strap hinges.

1. Remove the fuel tank support strap hinges and remove the fuel tank support straps.

1. NOTE: An assistant may be necessary to remove the fuel tank .
   Lower the fuel tank from the vehicle.

I hope my assistance helped you and resolved your concern, if you need further assistance please ask.

Removal & Installation

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Relieve the fuel system pressure.
3. Drain the fuel tank.
4. Remove or disconnect the following:
   
   Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump
   

To install:

1. Install or connect the following:
   
   Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
   
2. Fill the fuel tank.
3. Start the engine and check for leaks.
   
   

Check your fuel pressure.
Hopefully this tank is not full, as you need to pull the tank to change fuel pump, this is mounted onto the tank through the top. There are several plastic fitting and hose connecitons on the tank as well as the fuel level connector. There may also be a Vapor pressure sensor on the tank. After unbolting the tank lower the tank just far enough to remove the wireing and hoses. Make sure top of tank is clean. If you have to move tank out from under Blazer cover hose aconnectionss and wash off top of tank and flange area. Unlock flange and R and R pump assembly. Reconnect hoses and wires, reinstall tank. Connect hose to fuel test port on engine, purge air from fuel system. Check the fuel pressure. InMrFixIt

Usually the fuel filter is attached to the end of the fuel uptake hose inside the fuel tank... You need to access this hose (sometimes you can make a little wire hook to insert into the tank and draw the fuel uptake hose out)... If it is easily interchangeable this is how you would access it (on most chainsaw designs).

You can replace this hose alone but check all rubber fuel lines for cracks.

relief fuel pressure.remove air intake duct .the dohc engine remove the fresh air hose inlet hose from cam shaft cover.disconnect large under hood fuel line.near intake manifold support bracket on the left side of vehicle. look under vechicle where gas tank is there is a fuel filter with disconnects.

changing them, also change the fuel filter if you havent done it in a while, better gas mileage, id just go to your local auto parts dealer and tell them you want a new fuel line linkage from the tank to the front connection, if there is one. not really sure if it goes all the way to the fuel rail or not, but if it does then have fun, drop the tank, remove hose, replace hose, replace fuel filter, replace other cracked hose, making the replacement hose as short as possible, dont cut it though, just a waste cuz your going to have to replace the rest of it anyways

Hi michael
:-*
Just follow the fuel hose from the carburator and see where it is entering in the fuel tank.Fill out the gas from the fuel tank.At the end of the fuel hose is the fuel filter.Take them out (hose filter and fuel filter),then change it.Disassembly the carb and carefully cllean the inner parts.
:-* best wishes savumihai71