I am trying to connect battery terminals to my EQT generator.

Go to web site for manual or Google it.

Coleman Powermate Generator 5000 Watts / 6250 Watts ...

? 3:27
https://www.youtube.com/watch?v=IROa5QfPqkU
Nov 8, 2012 - Uploaded by Carlos Roman
This 5000 watt generator is great for backup power at home or forpower ... Coleman Powermate Generator 5000 Watts / 6250 Watts ... This feature is not available right now. ... folding handle, 1 quart, of oil, and 25ft generator convenience cord. ... How to convert a generator recoil starter to an electric starter!

pull cord won t retract Power Generators Questions ... - Fixya

www.fixya.com > Forum > Tags > pull cord won t retract

Power Generators pull cord won t retract questions and answers. Ask your pull cordwon t ... Question about Powermate Powermate 5000W Generator. 2 Answers · I was running my coleman powermate 6250 gen power ... cord 6250 trips out ... The pullcord does not rewind onto the pulley when pulled. At first I thought it was ...

Best Portable Generator Reviews

Sometimes, after a long period of non use, you need to 'flash the field' of a generator. If your gen is electric start, this should not be the problem. If it is a pull start, maybe so. Go online and see if you can find a schematic of you gen and try to find the field connections. Sometimes just momentarily connecting a battery across the field terminals will do the trick

Have you tried flashing your generator? Sometimes the magnets in the generator loose their polarity. Google and YouTube "flashing a generator"
HFLASHING the GEN

Sometimes the magnets lose their polarity. This worked on my brothers $1200 gen. Its worth a try. Good luck!
Check all wires/connections first, Then try this-
(Remove spark plug wire first!)
To flash the field on a small home use generator, get an ext. cord & cut off the female end of it & strip the wires & connect the wires to a 12 volt car or lawn tractor battery, & plug the male end of the cord, into the 120 A.C. side of the generator.

Make SURE that the black wire which is POS/HOT on an A.C. cord, gets connected to the RED/POS. side of the auto battery, & the white wire on A.C. cord gets connected to the BLK./NEG. side of the battery. If the ext. cord wires are not black & white, then the smaller prong of the plug is the POS./HOT

Plug the other end of the ext. cord into the generators 120 volt side (**remove spark plug wire**) & pull the starter cord 4-5 times, then remove the ext. cord, reconnect the spark plug wire, start the unit & plug something of 120 A.C. volts in to see if it works. Then let it run for about a half hour with 2 - 150 watt lights to help re-generate the unit.


Read more:http://www.doityourself.com/forum/outdoor-gasoline-power-equipment-small-engines/188605-recharging-generator-field.html#ixzz29QwjlAOWere's one way-

If the pull start works, but the electric start doesn't try the following. Either give the battery on the generator a full charge, and if after a full charge it doesn't start, get a new battery.

This is what I assume is for the starter motor for the generator. I would use for this a #8 welding wire style cable. This will supply enough power for starting.

Remove the accessory drive belt. Disconnect the negative battery cable. Disconnect the generator electrical connector. Remove the engine harness terminal from the generator: - Slide the boot back along the cable. - Remove the engine harness cable nut (3). - Remove the engine harness terminal from the stud. Remove the generator bolts and generator. Install the generator. Install the generator bolts. Tighten the generator bolts to 50 N?m (37 lb ft). Install the engine harness terminal to the generator: - Install the engine harness terminal to the stud. - Install the engine harness cable nut (3). Tighten Tighten the engine harness cable nut to 13 N?m (10 lb ft). - Slide the boot over the generator stud. Connect the generator electrical connector (1). Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure . Install the accessory drive belt

I usually fix electrical problems by process of elimination. Disconnect the wires attached to generator and touch the battery cable to the battery if it still arcs disconnect the regulator. continue until you find whats pulling current from the battery.

Ford has a technical service bulletin out that may fit your concern.
ISSUE:
The charging system indicator may illuminate or vehicle may not start. This may be caused by a discharged battery due to a poor electrical connection at the generator terminal.

2.0L

1. Replace generator B+ cable with a new Cable (F5RZ-14300-FA).
2. Replace the generator B+ terminal with a new Terminal (F3RZ-10329-AB).
3. Install new B+ cable retaining nut and tighten to 10.6 ±1.6 N-m (8 ±1 lb-ft).

2.5L

1. Replace generator B+ cable with new Cable (F5RZ-14300-EA).
2. If the generator B+ terminal is damaged, replace the Generator (F6RZ-10346-BB).
3. Install new B+ cable retaining nut and tighten to 10.6 ±1.6 N-m (8 ±1 lb-ft).

You can download the manual here at there web site.

http://www.breville.com.au/products_detail.asp?prod=306#