Technics RS TR-272 Model Cassette Deck

Jeff hi! These parts are only available from the agents or the factories. Try to advertise and then buy a faulty unit on E-Bay

Original Technics RS D400 Cassette Deck panasonic 400 RS SERVICE MANUAL

I am sure there is one available or suitable sub . I wonder if technics would provide more information if you contacted them or a local electronics store.
A microcontroller may or may not be programmed for a specific purpose so, that also may be an issue if not purchesd froma source used for that device.

There is also a forum called tapeheads:

Technics RS-B49R - Tapeheads Tape, Audio and Music Forums

www.tapeheads.net >

http://www.tapeheads.net/showthread.php?t=49248


I found some links here and even a few sold for parts around 15 bucks:

Google



https://www.icom.co.jp/world/support/download/manual/disp_down.php?SWT=&ID=20010101177&GNR=Amateur&TYPE=Mobile&PDNM=IC-901A/IC-901E&INQWORDSWT=No&INQWORD=

Place the tape you want to record into the left deck, Then the blank tape into the right deck. Press play on the left deck and record on the right deck.

It may be opposite depending on which side your recording deck is on.

Which ever deck has record, place blank cassette into that one and the cassette you want to copy into the other deck.

Hope this helps and please rate thanks

Hi,
You thinking is right,just change the belt which is smaller.

press the synchro start button, the tape deck should now go to REC PAUSE, press the SPEED button till you get the required recording speed then press the synchro start again and it should start to record from deck 1 to deck 2.

make sure the tabs at the top of the tape you want to record on are intact,
if not just put a bit of sticky tape over holes.

hope this helps?

I own a RS-T24 as well and stumbled upon this thread while searching for this exact same solution. The RS-T24 generates no power on its own. It gets its power from, in my case, the SU-V75 amplifier. I still have a working SU-V75 and got the following readings out of the plug-in for the RS-T24 on the amp:

Left = pin 1 - (white wire)
Middle = pin 2
Right = pin 3

1-2 = 11.5 vac
1-3 = 23.0 vac
2-3 = 11.5 vac

Each unit (the EQ and the Processor) should have left/right in/out rca jacks as well as L/R tape in/outs. The EQ or processor use the receiver's tape loop and then provide a tape loop to replace the one they've used on the receiver.

You plug the first unit (let's say the Sound Processor into your receiver/amp as if it were a tape deck (Processor's outs connect to reciever's tape ins (play) while the Processor's ins connect to the receiver's tape outs (record).

Then you chain the EQ off the Processor in the same way (EQ outs connect to Processor's tape ins (play) and EQ ins connect to the Processor's tape outs (record).

Last you connect the tape deck to the EQ as follows. Tape deck outs connect to EQ's tape ins (play) and the tape deck ins connect to the EQ's outs (record).

This will put both the Sound Processor and the EQ in the receiver's tape loop. In order to have all the receiver's source signals routed through them you may have to engage a Tape Monitor switch or button somwhere on your amp which will route the tape loop to your speakers.

a system remote is the only option for you here. The deck does not have its own remote receiver. Sorry to break the bad news to you.

Just connect you EQ to your receiver as if it were a tape deck: EQ's outs connect to receiver's tape ins (play) and EQ's ins connect to receiver's tape outs (record).

Then you hook the tape deck up to the tape ins and outs on the EQ: Tape deck outs connect to EQ's tape ins (play) and tape deck ins connect to EQ's tape outs (record).

This will put the EQ in your receiver's tape loop. To hear the EQed signal with all receiver sources you'll need to engage the 'Tape Monitor' button or switch which will route the tape loop to the speakers.