IBM System Storage TS3200 Tape Library Model L3H - Tape library - 17.6 TB / 35.2 TB - slots: 44 - LT... (3573L3H) Tape Drive Logo

Related Topics:

Question about IBM System Storage TS3200 Tape Library Model L3H - Tape library - 17.6 TB / 35.2 TB - slots: 44 - LT... (3573L3H) Tape Drive

2 Answers

What is the ts3200 system storage default password?

Default password for ts3200?

Posted by rapillay on

2 Answers


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,185 Answers

Try the default password, "secure".

Posted on Dec 18, 2009


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 125 Answers

The default password for the user ID "Admin" is "secure". This appears on the IBM_System_Storage_TS3100_Tape_Library_and_TS3200_Tape_Library_Installation_Quick_Reference_GA32-0548-00.pdf:

-Logging on to the Web User Interface To complete the configuration of your library using the Web User Interface, follow the steps below. If you have a 2U library, proceed to the section, "Choosing Library Settings" on page 1-15.
1. On your host computer, open Internet Explorer.
2. In the browser address field, enter your library's IP Address.
3. When the login screen appears, enter the following:

Username: admin
Password: secure

Anybody knows the password for username "service"????

Posted on Feb 01, 2013

  • 1 more comment 
  • Barb Withrow
    Barb Withrow Sep 10, 2014

    Do you know how to unlock the Admin account when the wrong password has been entered?

  • CarlosIjalba Sep 11, 2014

    From the unit's front menu.

  • CarlosIjalba Sep 11, 2014

    From the TS3200 front menu, select Configure, Reset Passwords. This will restore the userIDs and passwords to the defaut values, and reset the unit, which will do a full inventory. But your access will be restored.


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


IBM ts3200 tape library default service password

You will need to contact IBM support and after providing proper I.D. verification , they should be able to give you a password which you will be able to use. Due to security issues with stored info, you will have to provide the proper ID info as the original purchaser. Best Wishes

IBM TS3200 Code 9F 08

The manual is online with IBM.
Chapter 8 explains the error codes and 9F (mean Error code) means Rotation range out of specification 08 9sub error code) means error during rotation initialisation, get range failed.
Then the manual says: "Isolating a library controller card versus accessor enclosure problem" on page 7-11
But I guess you better look it up yourself. If you don't have any parts, you have to contact IBM.
Look yourself? start in chapter 8, page 225 of the manual under this link.

Inventory lost - source probably empty

dear friend send me the solution i have seen the same recently with mine too

Error 9E 09

Error 9E 09

9E : Elevator range out of specification

Primary: Library Enclosure
Secondary: Library Controller Card
09 : Error elevator init

HE: drive broken: needs repair

Then raise a call with IBM Hardware:

How do I create a PMR (aka Service Request) for support?

Web user interface timeout please log in again message over and over even after I log out and try to log back in

This may be caused by a bus level communication problem, try a restart. Power down the computer, power down the library, power up the library, wait for the library to finish initialization and verify from the control panel it is in an online/ready state, power up the computer.

ReadyNAS 1000S

I found this link.

It says that to reset the default admin password you need to reinstall the firmware.

Default DHCP address is

I hope this helps

Password problem

On older LinkSys routers, the default username is blank and the default password is "admin." On newer Linksys routers, both the default username and the default password are set to "admin." Once you are past the login screen, you are able to reconfigure the LinkSys router
Not finding what you are looking for?


Ask a Question

Usually answered in minutes!

Top IBM Computers & Internet Experts

Brad Brown

Level 3 Expert

19166 Answers


Level 2 Expert

691 Answers

Cindy Wells

Level 3 Expert

6650 Answers

Are you an IBM Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides